Troubleshooting the RCU4601 Remote Control

T

Troubleshooting the RCU4601 Remote Control
Problem:	Solution:
Why can't I program the RCU4601 to operate my component?	You may be too far away from the component or at a wrong angle. This remote uses IR (infrared) technology to communicate with components. The remote sends the code and the component’s IR sensor reads the code. Therefore, there must be an unobstructed path between the remote and the IR sensor on the component. Move closer and make sure you point the remote at the component (VCR when programming the VCR·DVD key; TV when programming the TV key; cable box or satellite receiver when you're programming the SAT·CBL·DTC key). If you've entered all of the codes for your brand that are in the accompanying Code List and followed the instructions, try the Code Search method. You must put the remote in the correct mode by pressing the corresponding component key (TV, VCR·DVD, AUX or SAT·CBL·DTC) so the remote knows which component you want to operate. To program the 4-component universal remote to operate a combination unit (TV/VCR or TV/DVD), first try the VCR or DVD codes for your brand. Some units require that you program both the TV key (using the TV codes) and the VCR·DVD key (using the VCR or DVD codes) for full operation. To program the 4-component universal remote to operate a VCR/DVD combination unit, program the VCR key using the VCR codes and then program the AUX key using the DVD codes.
Why isn't the indicator light lighting up when I press a key on the RCU4601?	You must put the remote in the correct mode by pressing the corresponding component key (TV, VCR·DVD, AUX or SAT·CBL·DTC) so the remote knows which component you want to operate. You may have pressed an invalid key for the mode the remote is in (for example, RECORD only works in VCR Mode). Make sure the batteries are properly installed. Replace the batteries with two new AAA batteries.
Why isn't the RCU4601 operating my component?	You must put the remote in the correct mode by pressing the corresponding component key (TV, VCR·DVD, AUX or SAT·CBL·DTC) so the remote knows which component you want to operate. Remove any obstacles between the remote and the component. Make sure to aim the remote at the IR sensor on the component. Make sure the batteries are properly installed (See Battery Installation). Replace the batteries with two new AAA batteries.
Why isn't the RCU4601 performing commands properly?	You must put the remote in the correct mode by pressing the corresponding component key so the remote knows which component you want to operate. Make sure component is “ready” (e.g., DVD player has disc loaded; VCR has tape loaded, etc.). You may have pressed an invalid key for the mode the remote is in (e.g., RECORD only works in VCR mode). If operating a VCR to record, you must press the RECORD key two times. If you're trying to change channels, try pressing the OK key after entering the channel number as this is a requirement of certain models and brands. There is a possibility that a programmed code may only be able to control some of your component features (e.g., only turns a component on and off). Follow the steps provided for programming the remote (See Programming Section). If the component can be turned on and off, make sure you press the CHAN +/– key to see if the component responds. If not, try the next code from the list.
Why won't my VCR record when using the RCU4601?	As a safety feature, you must press the RECORD key twice to begin recording. Make sure the tape is properly loaded in the VCR. Make sure the tape is not write-protected. If the safety tab is removed the tape is write-protected and you cannot record onto that tape.
Why won't the RCU4601 change channels on my component?	You must put the remote in the correct mode by pressing the corresponding component key (TV, VCR·DVD, AUX or SAT·CBL·DTC) so the remote knows which component you want to operate. Press the OK key after you enter a channel number.
Why isn't my component's menu appearing on the screen when using the RCU4601 to access it?	Make sure your component(s) are turned on and your TV is tuned to the appropriate video source and use the input key to toggle through video sources connected to your TV. Menu access isn't supported for all brands. If that’s the case, you'll need to use your original remote control to access menu functions for these components.