Programming the One-For-All URC3021 Universal Remote Control (3 Devices)

Programming the One-For-All URC3021 Universal Remote

Programming Device Control:

The One For All 3 Device Universal Remote Control is preprogrammed at the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola cable box.To control devices other than the default brands,perform the following steps; otherwise skip this section:

1. Turn on a desired device (e.g.,VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program
before starting step 2.

2. On the remote control,press a device key once (i.e., DVD/VCR, CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection, volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR) Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR) Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice, then release SET.

4. Use the Manufacturer’s Codes (starting on page 18) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.

5. Aim the remote control at the device and press POWER once.The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn't work, try Searching For Your Code on next page.

NOTE: If the device does not have a POWER key, press PLAY.

6. Repeat steps 1 through 5 for each device you want to control. For future reference,write down each working device code.

Searching For Your Code:

If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code.

NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and insert the required media.

For example, to search for a code for your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off (after pressing POWER). If the device does not have a Power key, you can substitute another function, such as digits 0 ~ 9 , CH, or PLAY).

NOTE: In the search mode, the remote control will send IR codes from
its library to the selected device, starting with the most popular code
first.

5. To lock in the code, press and release SET.The LED will blink twice.

6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for.

Checking Your Codes:

If you have set up the remote control using the Searching For Your Code procedure as above, you may need to find out which four-digit code is operating your equipment. For example, to find out which code is operating your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 0.The LED will blink twice.

4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8.

NOTE: If a code digit is “0”, the LED will not blink.

5. Repeat step 4 (on the previous page) three more times for remaining digits.Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Write down the code digits.

6. To check for codes of other devices, repeat steps 1 through 5 (starting on the previous page), but substitute the appropriate device key for each device you are checking. Write down the device’s code digits.

Programming a Master Power Macro:

In its default state, the POWER key on the One For All 3 Device Universal Remote Control will individually power your home entertainment devices on or off. However, you can also program a Master Power Macro onto the POWER key that will sequentially turn on or off all the devices with a single key press.

Programming The Power Key For The Master Power Macro

1. Press and hold SET until the LED (red light) blinks twice,
then release SET.

2. Enter 9 - 9 - 5.The LED will blink twice. Then press POWER once.

3. For the first device you want in the power-on sequence, press its device key (e.g., CBL/SAT) once.

4. Repeat step 3 up to two more times to add desired devices to the power-on sequence (e.g., DVD/VCR and TV).

5. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET.

Operating the Master Power Macro:

1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices.

NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off.

2. Devices will turn on (or off) according to your programmed
sequence.

NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device.

NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s).This action is normal.

Clearing the Master Power Macro:

1. Press and hold SET until the LED (red light) blinks twice, then release SET.

2. Enter 9 - 9 - 5.The LED will blink twice. Then press POWER once.

3. Press and hold SET until the LED blinks twice, then release SET.The Master Power Macro is now cleared.

Clearing Custom Programming

The One For All 3 Device Universal Remote Control contains an Operational Feature Reset program. If desired, you can use it to clear custom programming, except your setup codes and reassigned device keys, and reset them to original factory settings.Also see Restoring Factory Default Settings below.

IMPORTANT: Executing this program will erase all your custom settings for Power Macro, Favorite Channels, and Volume Lock.

1. Press and hold SET until the LED (red light) blinks twice, then release SET.

2. Enter 9 - 8 - 0.The LED will blink twice. The remote control
will return to normal operation.

Restoring Factory Default Settings:

The One For All 3 Device Universal Remote Control also contains a Factory Reset program that you can use to reset all custom settings and setup codes to original factory settings.Also see Clearing Custom Programming above.

IMPORTANT: Executing this program will erase all your custom settings for Power Macro, Favorite Channels,Volume Lock,Reassigned Devices, and all device settings.

1. Press and hold SET until the LED (red light) blinks twice, then release SET.

2. Enter 9 - 8 - 1.The LED will blink twice. The remote control will return to normal operation.

For more information, please refer to your  User's Manual