Using Macros on the One-For-All URC10820 Universal Remote

Programming a Favorite Channel With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, let's assume your favorite cable programs are on channel 52. Use the following instructions to program a macro key for direct access of this channel: NOTE: This example assumes the TV is tuned to the correct Input to view your cable box. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Select an open macro key (e.g., M1) and press it once. 4. Press CBL once. 5. Enter the channel number: 5 2. NOTE: If you have access to over 100 channels, enter 0 5 2. Moreover, if the original remote control requires you to press ENTER to change the channel, also press ENTER after the channel number (e.g., 0 5 2 ENTER). NOTE: You can program up to 20 functions on the macro keys. 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press M1, you will instantly see cable channel 52 on your TV set	Programming a Master Power Macro  In its default state, the POWER key on the One For All 10L Universal Remote Control with Learning (URC10820 B00) will individually power your home entertainment devices on or off. However, you can also program a Master Power Macro onto the POWER key that will sequentially turn on or off all the devices with a single key press. To Program the Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Press the POWER key once. 4. For the first device you want in the power-on sequence, press its device key (e.g., TV) once. 5. For the second device you want in the power-on sequence, press its device key (e.g., CBL) once. 6. For the Third device you want in the power-on sequence, press its device key (e.g., AUD) once. 7. Repeat step 6 up to seven more times to add the other desired devices to the power-on sequence (e.g., SAT, VCR, DVD, CD, PVR, AUX1 and AUX2). 8. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET.
Programming a Macro on a Device Key In its default state, when you press a device key (e.g., TV) on the One For All 10L Universal Remote Control with Learning (URC10820 B00), the remote will switch to that selected device. However, you can also program a Macro onto the Device keys to allow for additional functionality. For example, if your devices are connected to a receiver unit, you can program a Device macro to switch the receiver's input to the selected device. To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Press the DVD key once. 4. Press the AUD key (to select the receiver). 5. Press digit 3 (for the input), and press DVD (to return control to the DVD key). 6. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: You can program up to 20 functions on the Device Key Macro. You can program a device Key Macro onto any device key	Operating a Master Power Macro To Operate Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When you press POWER for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. 2. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s).This action is normal.
Operating the Device Key Macro 1. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. NOTE: When you press the device key (e.g., DVD) for less than 2 seconds, the remote will only select the DVD mode but will not change the Input on the receiver. This allows you to still change modes while using the remote. After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device.	Clearing a Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Select a macro key (e.g., M1, M2, M3 POWER or any device key) you want to clear and press it once 4. Press and hold SET until the LED blinks twice, then release SET. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function.

You can also refer to the Owner's Manual