Programming the ONEFORALL OARK02R Kid's Remote

Programming the One-For-All OARK02R Kid's Remote

Set the remote to control your TV:

Setting up the remote to control your TV will allow you to operate your TV's volume and mute.

1. Locate the three position switch inside the battery compartment. Set the switch to the middle position (P). This puts the remote in Programming mode.
2. When programming is complete, set the switch to either Child or Adult user modes before replacing the battery compartment door.

To program using Code Input:

1. Make sure your television is on.
2. Press the VOL+ key on the Kid's Remote. The remote's LED blinks twice.
3. Refer to the TV codes in the accompanying code list. Find your TV brand and use the remote's number keys to enter the first code for that brand. When you press the fourth number key, the LED on the remote blinks twice to confirm a valid code.
4. To test the TV code, slide the switch on the back of the remote to Child mode.
   Note: The remote must be in Child or Adult mode to test the code.
5. Point the remote at the TV and press Mute.
6. If the TV is muted then the code is correct. If the TV did not mute then try the next code for your brand. Repeat steps 1-4 in this section with the second code. Keep trying codes until the TV responds to Mute.

To program using Code Search:

1. Make sure your television is on and the remote is in programming mode.
2. Press the CH+ key. The LED blinks twice.
3. Press the On/Off key once.
4. Press the CH+ key once per second until the TV turns off.
5. When the TV turns off, press On/Off key.
6. If the TV turns on, press Mute to save the TV code. If the TV does not turn on, press CH- to go the previous TV code and press Mute once the TV turns on.

Note: There are over 200 possible codes, so the code search may take a few minutes.

If you have a different program provider...

If you have a different program provider (like cable or Dish Network), follow the instructions below to program the remote to operate your cable box or satellite receiver.

Note: If you have DIRECTV service, you can ignore these instructions - the remote is already programmed to operate your satellite receiver.

1. While in Child or Adult mode, hold down both Mute and On/Off for three seconds until the LED blinks twice.
2. Enter 9 8 2.
   If the LED blinks 4 times then go to the next step.
   If the LED blinks twice (or not at all) then start from step 1 again.
3. Put the 3-position switch in Programming mode (P).
4. Press the VOL- key. The LED blinks twice.
5. Find your satellite receiver or cable box brand in the accompanying code list.
6. Enter the first code for that brand with the number keys on the remote. When you press the fourth number key, the LED on the remote blinks twice to confirm a valid code.
7. Slide the 3-position switch to Child or Adult mode.
8. Press CH+ to see if the cable box or satellite receiver changes channels.
   If the channel changes, the remote control has been set.
   If the channel does not change, repeat steps 1 through 3 for the next code for that brand of set-top-box.
   If the LED flashes one long blink, the entry failed and must be repeated.

Test the Network Keys:

The Kid's Remote keys with network logos on them are preprogrammed to tune directly to those networks on DIRECTV receivers. Because channel lists and lineups can vary, it's a food idea to test these keys to make sure they go to the right channels on your DIRECTV receiver.

To test the network keys:

1. Point the Kid's Remote directly at your DIRECTV receiver.
2. Press a key with a network logo on it.
   If the receiver tunes to the right network then that key is correct. Please try the next one.
   If the receiver tunes to a different network then that key needs to be reprogrammed. Make a note of the key that needs to be reprogrammed and find the channel number for that network in your channel lineup.
3. If you find any network keys that need to be reprogrammed, follow the steps below to set the key(s) to the correct channel number(s).

Reprogramming Favorite Channel Keys:

The Kid's Remote comes pre-programmed with 8 DIRECTV kid's channels assigned to the logo keys. The pre-programmed keys can be programmed to new channel by following the steps below.

Caution: This will program over the channel that was pre-programmed at the factory.

To program a favorite channel:

1. While in Programming mode, press and hold the key that you wish to assign a favorite channel. The LED blinks twice. Release the key.
2. Press the digits for the channel number for the favorite channel that you wish to add.
3. Press and hold the key that you wish to assign again until the LED blinks twice.
4. Repeat steps above to assign another favorite channel.
5. If the LED flashes one long blink the entry failed and must be repeated.

Note: The Kid's Remote package comes with sticker you can use to place over any keys you've reprogrammed. Label the sticker first, then peel it off the sheet and place it on top of the key.

Program the Star and Moon Keys:

The Kid's Remote comes pre-programmed with 8 kid's channel assigned to the keys with logos on them. Two additional favorite channels can be added to the Star (1) and Moon (2) keys on the remote.

1. While in Programming mode, press and hold the Star (1) key. Release the key when the LED blinks twice.
2. Press the digits for the channel number for the favorite channel that you wish to save tot the Star (1) key.
3. Press and hold the Star (1) key until the LED blinks twice. The Star (1) key is programmed to the channel that you have assigned.
4. Repeat the steps above to assign a favorite channel to the Moon (2) key.
5. Slide the switch on the back of the remote to Child mode. Child mode is for children and limits them to only have access to the ten programmed channels on the remote.
6. Finally, secure the battery compartment back in place with a Phillips screwdriver.

Changing Power Control Settings:

The On/Off key has a default setting to control power on both the DIRECTV receiver (or cable box if reprogrammed) and TV each time it is pressed. To change this power control setting:

1. In Child or Adult mode, hold down both Mute and On/Off for three seconds, until the LED blinks twice.
2. Enter 9 9 5. The LED blinks twice.
3. Press On/Off.
4. Decide what you want the On/Off key to turn on and off and in what order. Then press the correct key from the following chart:
   
   
   
   
5. Press and hold Mute until the LED blinks twice.

Changing Volume Control Settings:

Volume control functions are defaulted to the TV that the remote is set to control. The volume control setting can be changed by following these instructions:

1. In Child or Adult mode, hold down both Mute and On/Off for three seconds until the LED blinks twice.
2. To control volume on satellite receiver: Enter 9 9 3. The LED blinks twice. Press Vol- to lock volume control to the satellite receiver. The LED blinks twice.
   
   or
   
   To control volume on TV: Enter 9 9 3. The LED blinks twice. Press Vol+ to lock volume control to the TV. The LED blinks twice.

Changing Channel Control Settings:

Channel control functions are defaulted to a DIRECTV satellite receiver. The channel control setting can be changed to be through the TV by following these instructions.

1. While in Child or Adult mode, hold down both Mute and On/Off for three seconds, until the LED blinks twice.
2. To control channel on TV: Enter 9 7 3 and press Vol- to lock channel control to the TV. The LED blinks four times.
   
   or
   
   If your channel control is set to TV, to change it back to satellite receiver: Enter 9 7 3 and press Vol- to lock channel control to the DIRECTV satellite receiver. The LED blinks twice.

For more information, please refer to your Owner's Manual.