Programming the One-For-All URC3110 Universal Remote Control

Programming the One-For-All URC3110 Universal Remote

Setting Up Your Components:

The One For All 3 Devices remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a Toshiba DVD player.To control devices other than the default brands, perform the following steps; otherwise skip this section:

NOTE: For TV/VCR Combo control, see the next section.

1. Turn on a device (e.g.,VCR) and, if applicable, insert media, (e.g., cassette or disc).

NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.

2. On the remote control,press a device key once (i.e., VCR/DVD,
CBL/SAT,or TV).Press and hold SET until the LED blinks twice,
then release SET.

3. Use the Manufacturer’s Codes (starting on page 11) to locate the
type of device and brand name and then enter the first four-digit
code for your component. If performed correctly, the LED will blink
twice.

NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again.

4. Aim the remote control at the device and press POWER once.
The device should turn off. If it does not respond, repeat
steps 2-3, trying each code for your brand until you find one
that works. If it still does not work, try Searching For Your
Code.

NOTE: If the device does not have a POWER key, press the (PLAY) key.

5. Repeat steps 1 through 4 for each device you want to control.

Programming TV/VCR Combo Control:

Perform the following instructions to control a TV/VCR Combo:

1. Turn on the TV/VCR Combo and insert a video cassette.

NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2.

2. On the remote control,press VCR/DVD. Press and hold SET until
the LED blinks twice, then release SET.

3. Use the Setup Codes For TV/VCR Combos (on page 12) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again.

4. Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code.

NOTE: If the device does not have a POWER key, press the (PLAY) key

Programming TV/DVD Combo Control:

Perform the following instructions to control a TV/DVD Combo:

1. Turn on your TV/DVD and insert a disc.

2. On the remote control, press VCR/DVD. Press and hold SET
until LED blinks twice, then release SET.

3. Use the Setup Codes For TV/DVD Combos (Access the Code List Here) to locate the brand name and then enter the first four digit code for your device. If performed correctly, the LED will blink twice.

4. Aim the remote control at your TV/DVD and press POWER. Your TV/DVD should turn off. If your original TV/DVD remote control did not have a POWER key, press PLAY.Your TV/DVD should start to play. If your TV/DVD does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your TV/DVD.

5. Your One For All 3 Devices is now programmed to operate your TV/DVD. Write your TV/DVD code for future reference. Remember, if you want to use your One For All 3 Devices to operate your TV/DVD, press the VCR/DVD key first.

Searching for your Codes:

If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code.

For example, to search for a code for your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off.

NOTE: In the search mode, the remote control will send IR codes
from its library to the selected device, starting with the most popular
code first.

5. To lock in the code, press and hold SET until the LED blinks twice, then release SET.

6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for

Checking the Codes:

If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment:

For example, to find out which code is operating your TV:

1. On the remote control, press TV once.

2. Press and hold SET until the LED blinks twice, then release SET.

3. Enter 9 - 9 - 0.The LED will blink twice.

4. To view the code for the first digit, press 1 once.Wait 3 seconds, count the LED blinks (e.g., 3 blinks = 3) and write down the number.

NOTE: If a code digit is “0”, the LED will not blink.

5. Repeat step 4 three more times for remaining digits.Use 2 for the
second digit, 3 for the third digit, and 4 for the fourth digit.

6. To check for codes of other devices, repeat steps 1 through 5, but
substitute the appropriate device key for each device you are checking.
As before,write down each four-digit code.

Re-Assigning Device Keys:

The One For All 3 Devices can be set to control a second TV,VCR, or DVD player.

For example, to control two TVs, a VCR, and a cable box, you will need to re-assign the unused VCR/DVD key to operate the second TV as follows:

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 2.The LED will blink twice.

3. Press TV once, then press VCR/DVD once.

4. The VCR/DVD key is now ready to be programmed for your second
TV. (see Setting Up Your Components). To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components:

To Re-Assign Key Sequence Perform
VCR/DVD as 2nd TV key: SET - 9 - 9 - 2 - TV - VCR/DVD
VCR/DVD as 2nd CBL key: SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD
VCR/DVD as 2nd SAT key: SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD
VCR/DVD back to VCR/DVD: SET - 9 - 9 - 2 - VCR/DVD - VCR/DVD

When a re-assignment is done, the LED will blink twice to confirm your
choice.At that time, you will need to program the remote control for the
new device (see Setting Up Your Components). User Manual

Changing the Volume Lock:

The One For All 3 Devices is set to control the volume of your TV in the
TV,VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e.g., CBL/SAT), change the Volume Lock as follows:

To Change Volume Lock To Another Mode:

1. On the remote control, press and hold SET until the LED
blinks twice, then release SET.

2. Enter 9 - 9 - 3 and then press any mode key once (except TV). The LED will blink twice.

3. Now, whenever you press VOL+, or VOL–, volume will be controlled by your mode choice.

Unlocking Volume Control:

NOTE: Perform these instructions when you want independent volume control for each programmed device (e.g., TV volume control in TV mode, CBL/SAT volume control in CBL/SAT mode, etc.)

1. On the remote control, press and hold SET until the LED
blinks twice, then release SET.

2. Enter 9 - 9 - 3 and then press VOL+.The LED will blink four times.

3. Volume will again be controlled according to its default states.

For more information, please refer to your  User's Manual