|
Programming a Favorite Channel With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, let's assume your favorite cable programs are on channel 52. Use the following instructions to program a macro key for direct access of this channel: NOTE: This example assumes the TV is tuned to the correct Input to view your cable box. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Select an open macro key (e.g., M1) and press it once. 4. Press CBL once. 5. Enter the channel number: 5 2. NOTE: If you have access to over 100 channels, enter 0 5 2. Moreover, if the original remote control requires you to press ENTER to change the channel, also press ENTER after the channel number (e.g., 0 5 2 ENTER). NOTE: You can program up to 20 functions on the macro keys. 6. Press and hold SET until the LED blinks twice, then release SET. Now when you press M1, you will instantly see cable channel 52 on your TV set |
Programming a Master Power Macro In its default state, the POWER key on the One For All 10L Universal Remote Control with Learning (URC10820N) will individually power your home entertainment devices on or off. However, you can also program a Master Power Macro onto the POWER key that will sequentially turn on or off all the devices with a single key press. To Program the Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Press the POWER key once. 4. For the first device you want in the power-on sequence, press its device key (e.g., TV) once. 5. For the second device you want in the power-on sequence, press its device 6. For the Third device you want in the power-on sequence, press its device key (e.g., AUD) once. 7. Repeat step 6 up to seven more times to add the other desired devices to the power-on sequence (e.g., SAT, VCR, DVD, CD, PVR, AUX1 and AUX2). 8. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. |
|
Programming a Macro on a Device Key In its default state, when you press a device key (e.g., TV) on the One For All 10L Universal Remote Control with Learning To Program the Device Key Macro For example, let's assume that your DVD in connected to Input 3 of your receiver. You can program a macro that will switch the receiver's input to input 3 when you press and hold the DVD key. 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Press the DVD key once. 4. Press the AUD key (to select the receiver). 5. Press digit 3 (for the input), and press DVD (to return control to the DVD key). 6. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. NOTE: You can program up to 20 functions on the Device Key Macro. You can program a device Key Macro onto any device key |
Operating a Master Power Macro To Operate Master Power Macro 1. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When you press POWER for less than 2 seconds, a power command will only be sent to the currently-selected device. This allows you to still individually power devices on or off. 2. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s).This action is normal. |
| Operating the Device Key Macro
1. After programming, point the remote control at the receiver and press the DVD key for at least 2 seconds. This will switch the Receiver's input to input 3, to allow you to view the DVD. After executing the Device Key Macro, the remote will return to the DVD mode, to allow the control of the DVD device. |
Clearing a Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 2. Enter 9 9 5. The LED will blink twice. 3. Select a macro key (e.g., M1, M2, M3 POWER or any device key) you want to clear and press it once 4. Press and hold SET until the LED blinks twice, then release SET. The macro is now deleted but the keys (in the case of POWER and device keys), will retain their original function. |
You can also refer to the Owner's Manual
STILL NEED HELP?- We use an automated support system so we can serve our customers in a first in - first out manner and prevent long hold times on the telephone systems
FIRST
- Feel free to search the knowledge base by entering your model number or keyword in the search box on the Support Home Page or on the Answer Page , then push the red search button to find additional answers available as this answer may be only one of the many available answers in our system for your product.
NOTE: Search for a MODEL NUMBER, searching for words like purchase or, warranty will get you far to many results and make finding the answer you are looking much more difficult
REACHING CUSTOMER CARE
If searching the answers in our Knowledgebase did not answer your question and you need additional information, support, warranty service or want to inquire about out of warranty repair please follow one of the steps below to use the automated support system
1. New to the Support Site :
Click here to go to the Support Account Creation Page so you can submit a support request and we can respond.
2 . Returning Customer:
Click Here to Go to the Ask A Question Page so you can submit a support request and we can respond. Note: You may have to login if you haven't already.
Comments
0 comments
Article is closed for comments.