Troubleeshooting the RCA RCR4258N Universal Remote Control
|
Why does the RCA RCR4258N remote does not operate your component? |
- You must put the remote in the correct mode by pressing the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL) so the remote knows which component you want to operate.
- Remove any obstacles between the remote and the component. Make sure to aim the remote at the IR sensor on the component.
- Make sure the batteries are fresh and are properly installed. (See Battery Installation on page 3.) Replace the batteries with two new AA batteries, if necessary. Reprogramming may be required.
- Reset the remote. Remove the batteries, then press and hold the number 1 key on the remote for several seconds to reset the
microprocessor inside the remote. Release the number 1 key, reinstall the batteries, and press the ON·OFF key. If it lights up, reprogram the remote and try again. If it doesn't light up, replace the batteries with new ones.
|
Why can't the RCA RCR4258N remote be programmed to operate your component? |
- If you are testing the remote after you have entered the code, you may be too far away from the component or at a wrong angle. This remote uses IR (infrared) technology to communicate with components. The remote sends the code, and the component’s IR sensor reads the code. Therefore, there must be an unobstructed path between the remote and the IR sensor on the component. Move closer and make sure you point the remote at the component (DVD player when programming the DVD key; TV when programming the TV key; satellite or cable box when programming the SAT·CBL key, VCR or auxiliary component when programming the VCR·AUX key).
- If you've used the Direct Entry programming methods to enter the codes for your brand and the unit is still not functioning properly,
try one of the Code Search methods. (See pages 4-9.)
- To control combo units, like TV/VCRs, TV/DVD's or TV/VCR/DVD's, you must program the individual corresponding
component keys to control each part of the combo unit. Once programmed successfully, the TV key controls the TV functions, and the VCR·AUX or DVD key controls the VCR or DVD functions, respectively. There is a specific section in the Code Lists for combo units. The codes in this section should be tried first using Direct Code Entry on the TV and DVD or VCR·AUX keys. If this is unsuccessful, follow the normal programming methods for both the TV and the DVD or VCR·AUX keys.
- Make sure the batteries are fresh and are properly installed.
|
Why is the RCA RCR4258N remote is not performing commands properly? |
- You must put the remote in the correct mode by pressing the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL) so the remote knows which component you want to operate.
- Make sure component is “ready” (e.g., DVD player has disc loaded; VCR has tape loaded, etc.)
- You may have pressed an invalid key for the mode the remote is in.
- If you're trying to turn on an RCA, GE or PROSCAN component,
press the component key (TV, DVD, VCR·AUX, SAT·CBL) instead of the ON·OFF key.
- If you're trying to change channels, try pressing the OK key after
entering the channel number as this is a requirement of certain models and brands.
- There is a possibility that a programmed code may only be able to control some of your component features (e.g., only turns a component on and off). To confirm that the component key is programmed with the correct code for maximum functionality, test the component. Attempt to control a variety of the component’s functions with the remote. If some of the features of your components do not work, try programming the remote with a different code in the list using the Direct Code Entry Method, until you find the code that allows the remote to control the majority of your component’s functions. Different codes can provide different levels of functionality.
|
Why does the illuminated ON·OFF key not light when you press a key on the RCA RCR4258N? |
- You may have pressed an invalid key for the mode the remote is in. You must put the remote in the correct mode by pressing the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL) so the remote knows which component you want to operate.
- Make sure the batteries are fresh and are properly installed. Replace the batteries with two new AA batteries, if necessary. Reprogramming may be required.
|
Why won't the VCR record using the RCA RCR4258N? |
- Make sure the remote is in VCR Mode.
- Make sure the tape is properly loaded in the VCR.
- Make sure the tape is not write-protected. If the safety tab is removed the tape is write-protected, and you cannot record onto that tape.
|
Why won't the RCA RCR4258N remote will not change channels on component? |
- You must put the remote in the correct mode by pressing the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL) so the remote knows which component you want to operate.
- Press the OK key after you enter a channel number.
- Remove any obstacles between the remote and the component. Make sure to aim the remote at the IR sensor on the component.
|
Why does the RCA RCR4258N component’s menu not appear on the TV screen? |
- Make sure you have connected your component to your TV properly and selected the correct input. (See your components’ Owner’s Manuals for proper connection procedures.)
- You must put the remote in the correct mode by pressing the corresponding component key (TV, DVD, VCR·AUX, SAT·CBL) so the remote knows which component you want to operate.
- Menu access isn't supported for all brands. If that’s the case, you'll need to use your original remote control to access menu functions for these components.
|
How do I reset the RCA RCR4258N Remote ? |
First Step Find the battery compartment on the back of the remote. You will need to open the battery compartment to reset the remote. How you open it depends on the kind of remote you have...
If the battery compartment door on your remote is held in place by a latch
- Press the latch back to release the door and pull up to open the compartment
If the battery door does not have a latch
- Simply press the compartment door and slide it off of the battery compartment.
Reset steps:
- Remove the batteries
- Press and hold down the #1 button on the keypad for 60 seconds - Note: You may need to do this 3-5 times to clear the remote.
- Insert batteries
- Begin reprogramming - Note: After resetting the remote control, reprogramming is required.
IMPORTANT: If your remote model ends with an "N", this procedure will not reset your remote
|
Why does the indicator light flash on the RCA RCR4258N while I am programming the remote control for a component? |
- The indicator light will flash while programming the remote control for a component if the code entered is invalid. Check the code list and reprogram the remote control.
|
Comments
0 comments
Please sign in to leave a comment.