Additional Remote Features for PRO9900 Remote Start System

Transceiver Icons and Their Indications for PRO9900 Remote Start Security System
	When Disarmed, Press the Arm/Lock button to Lock and Arm the System. The Lock Icon is displayed on the LCD panel and the parking lights flash once. When Armed, Press the Disarm/Unlock button to Unlock and Disarm the System. The Unlock Icon is displayed on the LCD panel and the parking lights flash twice. When the Key Icon Button has been operated for 3 seconds the trunk open icon will flash on the LCD screen. If text mode was selected, the words Trunk Open will appear and remain on the screen until the trunk is shut.
	When the Key Icon Button is pressed 2 times in succession three puffs of smoke are displayed on the LCD screen while the vehicle is running. The exhaust indication will flash and the hour glass will indicate count down timer based on the 5, 10, 15, or 20 minute run time set up by your installation center. When the unit shuts off the exhaust indication will turn off and the transmitter will play a melody. Note: The engine can be started in many modes; armed, disarmed, valet, etc... The screen shown is Locked/Armed and running.
	When the Panic Mode has been activated and the system is armed the vehicle's lights will flash, the siren and lock icon will be displayed on the LCD screen and the siren will beep. If the system is disarmed and the Panic Mode is activated, the lights will flash, the unlock icon will be displayed and the siren will beep on the LCD screen.
	Whenever the vehicle is operated from the two way transmitter, the unit will beep responsive to the function executed at the vehicle. 1 beep when armed, 2 beeps when disarmed, etc... At times it may be inconvenient or too noisy to hear the beep tones, so the system allows you to set the unit for vibrate mode. To toggle on or off beep tones/vibrate; Simultaneously press the "F" and unlock buttons. The icon shown left will appear in the upper left hand corner of the screen to indicate vibrate.
	If the alarm system has been triggered, the icon displayed on the transmitter LCD will indicate which zone has been activated, as well as sound the beep tones, or vibrate dependent upon the setting. The following trigger patterns will be displayed. Triggered and the entry attempt was made to one of the vehicle Doors. Triggered and entry attempt was made to the vehicles Hood. Triggered and entry attempt was made to the vehicles Trunk. Triggered and entry attempt was made to the vehicle's glass, or the vehicle has been hit or bumped hard enough to cause a response from the vibration detector.
	If the Arm/Disarm chirp tones have been turned off at the vehicle, when you arm, or disarm, the display will indicate this as shown and there will be no arm/disarm chirps at the transmitter. This is true if the transmitter is set for vibrate mode.
	When the vehicle is armed, and a door is opened, or ajar, the transmitter will chirp 2 times, the lights will flash, and the display will indicate a door trigger as shown on the previous page. When the door is closed or the zone clears, the transmitter will chirp 1 time, and the display will clear. When the vehicle is armed, and the hood or trunk, is opened or ajar, the transmitter will chirp 3 times, the lights will flash, and the display will indicate a hood or trunk trigger. When the hood or trunk is closed, or the zone clears, the transmitter will chirp 1 time, and the display will clear.

Additional Remote Features for PRO9900 Remote Start Security System
	The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display, toggle the transmitter from beep tones to vibrate mode, initiate daily start timer, and temperature start. Selection of these and other features are shown below: Note: Transmitter must be within operating range of the vehicle, approximately 1000 ft. Check Vehicle Status: Press the lock+key+option buttons simultaneously for 1 second. The vehicle's alarm will display the system's current status. Check Temperature: (only available on certain remote start units) Press the option+key buttons simultaneously for 1 second. The vehicle's alarm will display the temperature. Temperature is read from the alarm's module located below the dashboard. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only to the inside vehicle temperature. Temperature Start Mode: (available on certain models) This icon will appear when the temp start mode is activated. The vehicle will start one time automatically when the temperature reaches 0*. To toggle this feature on or off, from the armed mode, press the option+unlock buttons simultaneously, the temperature icon appears, or disappears from the display, and the transmitter will emit a tone. Note: This feature must be active in the feature selection menu of your system. Check with your installation dealer to insure this feature is set to the on position. CAUTION: Be certain the vehicle is outside before activating this mode. To toggle this on or off, from the Locked/Armed Mode, press the option+lock buttons simultaneously. (Available on certain remote start models only.) Light the Display: Press and release the "F" (Function) button one time. The display will illuminate for 10 seconds. Vibrate or Tones: Press the "F"+unlock buttons simultaneously to toggle this feature on and off. Daily Start Timer: (Only available on certain remote start units) This icon is displayed when the 24 hour start timer is activated. Press the option+lock buttons simultaneously for 3 seconds. The transmitter will beep and display the 24hr timer. The vehicle will start automatically when the time set is reached. Pressing this button combination a second time will toggle this feature off. Note: The transmitter must be within range of the vehicle to set this feature and within range to cause the vehicle to start at the preset time. The unit will start at the prescribed time once only. This function must be selected each time you want the vehicle to start. To activate this function, (a) Turn the ignition switch off. (b) Within 10 seconds, depress and hold the brake pedal, while pressing the key icon transmitter button 2 times. (c) The unit will emit 2 chirps, the transmitter will beep and the start timer icon on the display will remain on. Note: To insure accurate 24 Hour Start Up, it is advisable to reset the start time periodically as time may drift slightly each day. Timing Count Down: The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. This additional count down timer allows you to set the count down up 19 hours and 59 minutes from the current time, when the timer reaches zero, the transmitter will emit a tone or vibrate dependent on your preferred setting. Valet: When the system is in the valet mode, the icon shown will show in the display when the status check buttons are activated. Parking Meter Counter: The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90, or 120 minutes. This feature is useful when parking the vehicle in a metered parking lot. If the time on the parking meter is 30 minutes, you can set the count down timer to 20 minutes. The transmitter will emit a beep tone when the timer expires to remind you to get back to your vehicle. Alarm Clock Mode: The transmitter has a built-in alarm clock that can be set to beep at a certain time each day. The alarm clock mode must be set, and the feature turned on. Note: Your system is shipped with two transmitters, 1 two way and 1 one way transmitter. The one and two way transmitters are programmed from the factory with separate lock & unlock buttons, the trunk/key icon button operates remote start and remote trunk release where applicable. The option button and any button combination may be programmed to operate various options. Consult your installation center for button programming and options that may have been added to your vehicle. Although this is the default programming from the factory, this can be changed for you to any configuration your prefer. Please refer to the transmitter program guides included with your kits. Note: A maximum of two of either style transmitter may be programmed to your unit.
	Battery Indicator: This icon indicates a new battery shown with 3 bars. As the battery deteriorates, the bars will disappear. 1 bar indicates the battery should be replaced. Replace battery with a fresh 1.5V AAA battery and dispose of the used battery properly. Range Indicator: This will have bars to the side of the icon if the unit is out of range. Vibrate Mode On: This icon will be displayed if you select vibrate instead of tones. Alarm Clock: This icon will be toggle on and off when the "F" + Trunk/Key buttons are pressed simultaneously. The feature must be set in the feature selection menu of the transmitter. Timing Count Down: The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important. Power Save Feature: Press the "F" + Lock buttons simultaneously to toggle this feature on and off. With this mode on, the battery in the transmitter will go into a power down mode when the unit is disarmed.

For more detailed operating instructions, please refer to your Owner's Manual.

Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.

Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.

NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.