Operating the Audiovox IPD2FM iPad Rear Seat Entertainment Mount

Operating the Audiovox IPD2FM iPad Rear Seat Entertainment Mount

1. Finger Push Out Window - To push out the iPad from the Protective Case.
2. 30 Pin Connector
3. Volume -/Volume + Buttons
4. Power On/Off Button - To turn the iPad on or off .
5. Camera Port
6. Mounting Arm - Attaches and locks the Protective Case to the Universal Seatback Dock.
7. DC 12V Charging Port - Power in jack for 12 V/1.5 A power adapter.
8. Red Switch - Hold to lock or unlock the Mounting Arm into Universal Seatback Dock.
9. Locking Key - Hold the key to insert or release the iPad.
10. Speaker Port
11. 3.5 mm Audio Out Port

To insert your iPad into the Protective Case:

Make sure the Locking Key is in the closed (pushed in) position so that it is flush within the case.

1. Slide your iPad into the Protective Case. Match the iPad charging connector with the Protective Case’s Open Base Port position and gently pull the Locking Key out while sliding the iPad into the case.
   
   
   
2. Push your iPad down into the Protective Case.
   
   
   
3. When your iPad is inside the Protective Case, slide the iPad to the left while at the same time pushing in the Locking Key.
   
   
   
4. Press the Locking Key to ensure the iPad is held firmly by the Protective Case.

To remove your iPad from the Protective Case:

1. Hold the iPad and Protective Case vertically.
2. Pull the Locking Key gently while holding the Protective Case in a vertical position. The iPad will slide down. Note: Please do not pull the Locking Key too hard when removing your iPad from the Protective Case to prevent damaging the locking parts.
   
   
   
3. Use your index finger to push your iPad out of the Protective Case using the Finger Push Out Window.
   
   
   
4. Remove your iPad from the Protective Case in the indicated direction.

To install the Universal Seatback Dock on the Headrest:

1. Adjust the headrest position.
   
   
   
2. Plug one end of the Vehicle DC Power
   Adapter into the DC 12V Charging Port on the bottom of the Universal Seatback Dock.
   
   
   
3. Turn Screws (A) counterclockwise and
   remove the Screws to disassemble the
   Universal Seatback Dock.
4. Clamp the Front Bracket (B) and Rear
   Bracket (C) around the headrest posts. Note the location of the bottom side engraved on the Rear Bracket. Ensure that this side is facing down and the slot is facing the rear of the vehicle.
5. Secure the brackets in place with the Screws. Turn the Screws clockwise and hand tighten.
6. Plug the other end of the Vehicle DC Power Adapter into the Vehicle DC Accessory Socket of your car.

To attach the Protective Case to the Universal Seatback Dock:

The Mounting Arm has six depth settings to allow for proper fitting to the seat depending on the size of the headrest.

Warning! Always make sure the Red Switch is in the UNLOCK position when inserting or removing the Mounting Arm, otherwise damage will occur to both units.

1. Hold the Red Switch in the UNLOCK position.
2. While holding the Red Switch in the UNLOCK position, insert the Mounting Arm into the slot in the Rear Bracket.
3. Once the Mounting Arm is inserted into the Rear Bracket sufficiently, release the Red Switch so that it returns to the LOCK position.
   
   Warning! Ensure the Mounting Arm is inserted and locked in the Rear Bracket before moving your vehicle.
4. Adjust the tilt angle to the desired viewing position.

To remove the Protective Case from the Universal Seatback Dock:

1. Hold the Red Switch in the UNLOCK position.
2. At the same time, pull the Mounting Arm out of the Rear Bracket.
3. When the Mounting Arm is fully removed from the Rear Bracket, release the Red Switch so that it returns to the LOCK position.