Operating Instructions for APS687N Remote Start System

Operating the Prestige APS687N Remote Start System
Keyless Entry Operation:	To lock the vehicle: Exit the vehicle and close all doors. Press the lock button of your transmitter. To unlock the vehicle:  Press the unlock button of your transmitter. Note: Holding the lock/unlock button for 3 seconds will activate the car finder mode causing the parking lights to flash for 30 seconds or until the button is activated again for 3 seconds or any other button is operated.
Additional Remote Function (Channel 3):	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Closure Remote Garage Door Interface To activate the optional accessory, press and hold the trunk/key button on the transmitter for 4 seconds.
Additional Remote Function (Channel 4):	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Window Defogger During Remote Start if vehicle is so equipped Rear Hatch Release Remote Window Closure Right or Left Slider Doors in an equipped van To activate the optional accessory, press the option button on the transmitter. The optional accessory will immediately engage.
Additional Remote Function (Channel 5):	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Closure Rear Hatch Release Right or Left Slider Doors in an equipped van To activate the optional accessory, press the option button on the transmitter. The optional accessory will immediately engage.
Additional Remote Function (Channel 6):	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Hatch Release Right or Left Slider Doors in an equipped van Driver Priority Settings in vehicles so equipped To activate the optional accessory, press the option button on the transmitter. The optional accessory will immediately engage.
Additional Remote Function (Channel 7):	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Hatch Release Right or Left Slider Doors in an equipped van Driver Priority Settings in vehicles so equipped Second Driver Priority Settings in vehicles so equipped To activate the optional accessory, press the option button on the transmitter. The optional accessory will immediately engage.
PRLED Safety Control Switch:	The control switch allows you to temporarily disable the remote starting function of the system. To place the system in the service mode: With the system disarmed/unlocked, and the ignition switch off, press and hold the PRLED on. Turn the ignition switch on, off, on, off. This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise. The LED begins to flash two short flashes followed by one long flash and continues this pattern until returned to normal mode of operation. To exit R/S Override mode: With the system disarmed, press and hold the PRLED on. Turn the ignition switch on, off, on, off, on, off. The LED turns off indicating the R/S unit is fully functional once again.
Turbo Timer Mode:	This system provides a means to cool down the vehicle's turbo charger, if so equipped, by allowing the vehicle to continue to run for a prescribed period of time every time the vehicle's engine is turned off. This feature required the system to be set up for turbo timer during installation. Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run after the ignition switch is turned off. To activate the turbo timer: Anytime the ignition key is in the on position for more than 15 seconds, place the gear selector in Park. Set the parking brake. Be certain your foot is off the brake pedal. Press the program/push-button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully entered. If you parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or release the parking brake, or activate the transmitter's start button two times in succession. Any of these will cause the engine to turn off.
Remote Starting the Vehicle:	This unit will not start if any one of the following situations exists: The vehicle's hood lid is opened. The gear shift selector is not in Park. The brake pedal is depressed. The system is placed in the override position. To start the vehicle: Press and release the trunk/key button on the transmitter two times within 2 seconds. The vehicle will start and remain running for the pre-programmed time. As a visual indication, the parking lights will flash or remain on depending on the setting by your installation center. When you arrive at the vehicle, unlock it with the key or by pressing and releasing the trunk/key button on your transmitter. Enter the vehicle and turn the ignition key to the on position (not the start position). Step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on its own power.
Operating on Automatic Start Up Timer Mode:	Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. To being the timer: Turn the ignition key on then off. Within 10 seconds, activate the RF start command two times (push the trunk/key button of your transmitter 4 times). The parking lights will flash indicating the timed start mode is activated. The vehicle on a 2 or 4 hour interval basis, will automatically start, run for the pre-programmed time and then shut off. This will continue for 48 hours. To start the timer using only the transmitter: Start the vehicle using the transmitter by pressing and releasing the trunk/key button on the transmitter 2 times. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/key transmitter button 2 times. Within 10 seconds, activate the RF start command two times (push the trunk/key button 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. To cancel the start timer, do one of the following: Start the vehicle manually with the use of the ignition key and depress the brake pedal. Remote start the vehicle using your keychain RF transmitter. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/key transmitter button 2 times.
Telematic Upgrade:	This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that can give you control of certain functions of your vehicle from a Telephone, or in some cases a computer interface. Please check with your installation center for the most recent Telematic Upgrades. If you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide an operator's manual advising you of the features of the system and means available to control these features of your vehicle.