Operating the Prestige APS620N Remote Start System
|
Keyless Entry Operation: |
The lock button is used to lock the doors, the unlock button is used to unlock the doors.
- Simply press and release the desired function button one time. As a keyless entry unit, when the doors are locked, the parking lights and/or horn will flash/beep once. When the doors are unlocked the parking lights and/or horn will flash/beep twice.
|
Remote Car Finder:
|
The lock or unlock buttons are also used to access the car finder mode.
- Simply press and hold either the lock or unlock button of your transmitter for 3 seconds.
- If you wish to turn off the panic mode before the 30 second timer, press and hold either the lock or unlock button a second time for 3 seconds or press and release the Trunk/Start button one time.
|
Remote Trunk Release: |
- If you have electric trunk release in your vehicle and the remote trunk release option was added, simply press and hold the Key/Trunk button for 4 seconds or until the electric trunk of your vehicle opens.
|
Remote Starting the Vehicle: |
This unit will not start if any one of the following situations exists:
- The vehicle's hood lid is opened.
- The gear shift selector is not in Park.
- The brake pedal is depressed.
- The system is placed in the override position.
To start the vehicle:
- Press and release the Key/Trunk button two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, 20 minute run cycle. As a visual indication, the parking lights will flash or remain on depending on the setting by your installation center.
- When you arrive at the vehicle, turn the ignition key to the on position (not the start position).
- Step on the brake pedal to disengage the remote starter. The vehicle will continue to run, but now on its own power.
|
The Option Button: |
This button may or may not be used with your system but may be used with a second similar Audiovox Model system that may be installed on a second vehicle in your family. |
Push-Button Safety Control / Program Switch: |
The push-button safety control switch allows you to temporarily disable the remote starting function of the system. This is recommended whenever the vehicle is being serviced.
To place the system in the service mode:
- With the system disarmed and the ignition switch off, press and hold the control switch on.
- Turn the ignition switch on, off, on, off, on, off.
To exit R/S Override Mode:
- With the system disarmed, press and hold the control switch on.
- Turn the ignition switch on, off, on, off, on, off.
|
Operating on Automatic Start Up Timer Mode: |
Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period.
To being the timer:
- Turn the ignition key on then off.
- Within 10 seconds, activate the RF start command two times (push the programmed channel button of your transmitter 4 times). The parking lights will flash and the siren will chirp 2 or 4 times indicating the timed start mode is activated.
- The vehicle on a 2 or 4 hour interval basis, dependent on the number of chirps head when activated as described above will automatically start, run for the pre-programmed time (5, 10, 15, 20 minutes) and then shut off. This will continue for 48 hours.
To start the timer using only the transmitter:
- Start the vehicle using the transmitter by pressing and releasing the second channel transmitter button 2 times.
- Shut off the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times.
- Within 10 seconds, activate the RF start command two times (push the second channel button 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated.
To cancel the start timer, do one of the following:
- Start the vehicle manually with the use of the ignition key and depress the brake pedal.
- Remote start the vehicle using your keychain RF transmitter.
|
Programming Transmitters: |
At times it may become necessary to program replacement or additional transmitters for use with your system.
Note: The unit is capable of storing up to 4 transmitters. If a fifth transmitter is added, the first transmitter programmed will be bumped out.
To do this:
- With the system unlocked or disarmed, turn the ignition key to the on position.
- Press and release the Program/Override push-button switch three times.
- The unit will flash the parking lights and or beep the horn once to indicate that the system is in the transmitter program mode.
- The LED will also flash one time pause, one time pause, etc... indicating that you are in the transmitter program mode of the unit’s channel 1 or single button program mode.
- Press and hold the lock button of each additional transmitter you wish to operate your system.
- Once all transmitter have been programmed, turn the ignition switch off to exit the program mode.
|
Deleting Transmitters from Your System: |
It may be necessary to delete a lost transmitter or to re-prioritize a transmitter that is programmed to your system. To remove a transmitter that has been programmed in your system:
- Enter the transmitter program mode of channel 1 as indicated above.
- Press and hold any transmitter button that has not been programmed into channel 1 until you hear a chirp, then release and immediately press the same button a second time until you hear a long chirp followed by a short chirp. This action erases the transmitter.
If the transmitter you wish to erase has been lost or stolen then following the information below will successfully remove the transmitter.
Note: For this procedure, you must have all transmitters you wish to remain programmed in your system available.
- Enter the transmitter program mode of channel 1 as indicated above.
- Press and hold the lock button of each transmitter you wish to operate the lock function of your unit making sure you occupy all 4 transmitter slots.
- In other words, you have three transmitters you wish to remain programmed. Press and hold the lock button of transmitter one until a long chirp is heard.
- Then press and hold the lock button of transmitter two, then press and hold the lock button of transmitter three, followed by pressing and holding the lock button of transmitter one again. This action fills all 4 receiver slots.
- Advance to receiver channel 2 by pressing the push-button switch one time. Press and hold the unlock button of each transmitter you wish to operate the unlock function of your vehicle, again making sure all 4 transmitter slots are filled.
- Advance to receiver channel 3 by pressing the push-button switch one time. Press and hold the unlock button of each transmitter you wish to operate the start function of your vehicle, again making sure all 4 transmitter slots are filled.
If you are uncomfortable about the programming of additional transmitters as outlined in the processes above please contact your installation center or call the technical service number listed on the back of the transmitter for help.
|
Comments
0 comments
Article is closed for comments.