Remote Operation for the Code Alarm CA670 Remote Start Alarm System

Remote Operation for the Code Alarm CA670 Remote Start Alarm System
Arming the Security System	To arm the system: Exit the vehicle. Close all doors. Press the LOCK icon button on the remote control. The system will sound twice and the parking lights will flash twice, indicating the system is armed. The doors will also lock at this time (if equipped and connected). The status indicator (blue warning light on the dash) will blink steadily, once per second. To arm the system silently: Press and hold the LOCK icon button for 1 second. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The status indicator (blue warning light on the dash) will blink steadily, once per second.
Pre-Arm Mode	If the horn system sounds and the parking lights flash only once, this indicates that the vehicle’s interior light is on or an entrance is left open. Check to see that all doors hood and trunk are closed properly. Once all entrances are secured (and the interior light is off), this system will sound/flash again. The system is now fully armed. (If the entrance is not secured within 4 minutes, the system will arm and ignore the unsecured entrance until it is closed.)
Disarming the Security System	To disarm the system: Press the UNLOCK icon button. The system will sound and the parking lights will flash once, and the doors will unlock (if equipped and connected). To disarm the system silently: Press and hold the UNLOCK icon button for 1 second. The parking lights will flash, indicating the system is disarmed and has unlocked the doors (if equipped and connected).
Disabling/Enabling Confirmation Chirps	Turn the ignition key ON then OFF. Within 10 seconds push and release the valet/override button 3 times. The system will sound 2 times to disable confirmation chirps or 1 time to enable confirmation chirps.
Attempted Intrusion Identification	This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt occurred, the system will sound 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle an observe the dash mounted status LED to Identify which zone was triggered. Shock Sensor- 1 flash, pause 1 flash, etc. Hood or Trunk Pin switch- 2 flashes, pause 2 flashes, etc. Door Entry- 3 flashes, pause 3 flashes, etc. The intrusion warning indicators are stored in the system’s memory and will be erased when the ignition key is turned on.
Two Stage Door Unlock (Optional)	If this feature is enabled on your system, pressing the UNLOCK icon button one time on the remote control will unlock only the driver’s door. Press disarm again to unlock the remaining doors.
Activating the Trunk Release Feature (Optional)	If this feature is enabled on your system, pressing and holding the TRUNK icon button on the remote control for 2 seconds will open the vehicle’s trunk or hatch.
Turning on the Vehicle's Headlights (Optional)	If this feature is enabled on your system, pressing and holding the LOCK icon button on the remote control for 2 seconds will turn on the vehicle’s headlights for 30 seconds.
Activating Optional Channel 2	If this feature is enabled on your system, pressing and holding the LOCK icon button and the TRUNK icon button on the remote control simultaneously will activate an Optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine functionality of your system.
Activating Optional Channel 3	If this feature is enabled on your system, pressing and holding the OPT button on the remote control will activate an Optional feature. Optional Channel 3 is generally used to turn on the rear window defroster after the vehicle has been remote started, but can also be programmed for a wide range of functions, please consult your installing dealer to determine functionality of your system.
Activating Optional Channel 4	If this feature is enabled on your system, pressing and holding the LOCK icon button and the OPT button on the remote control simultaneously will activate an Optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine functionality of your system.
Activating Optional Channel 5	If this feature is enabled on your system, pressing and holding the UNLOCK icon button and the OPT button on the remote control simultaneously will activate an Optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine functionality of your system.
Using the Progressive Car Finder Feature	2-way LCD Remote Control: Press the LOCK icon button and the UNLOCK icon button on the remote control to locate your vehicle. The system will sound 5 times at low volume increasing in volume each of 3 times the button is pressed. 1-way Six Button Remote Control: Press the “*“ icon button on the remote control to locate your vehicle. The system will sound 5 times at low volume increasing in volume each of 3 times the button is pressed.
Using the Personal Protection Alarm (Panic)	2-way LCD Remote Control: Press and hold the LOCK icon button and the UNLOCK icon button on the remote control for 2 seconds to activate the personal protection alarm. The system will sound for 30 seconds. Pressing any button on the remote control will turn the personal protection alarm off. 1-Way Six Button Remote Control: Press and hold the “*“ icon button on the remote control for 2 seconds to activate the personal protection alarm. The system will sound for 30 seconds. Pressing any button on the remote control will turn the personal protection alarm off.
Using the Transmitter Flashlight Feature	The (1) 6 button (non-confirming) remote control included with your system has a flashlight bulb built into the top of the remote control. Pressing and holding the LIGHT icon button on the remote control will activate the flashlight until the button is released.
Using Your Remote Vehicle Starter
Remote Starting Your Vehicle	To activate the remote vehicle start function: Press and release the OPT button on the remote control two (2) times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start, if all safety parameters are correct, the vehicle will start within 5 seconds (diesel vehicles will take longer). The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running. Press and release the OPT button on the remote control two (2) times within 2 seconds again to turn the vehicle off. If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the fourth attempt, the system will abort the remote vehicle start process.
Entering the Vehicle while it is running via Remote Vehicle Start	Unlock the vehicle’s doors. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL! Insert the key into the ignition switch and turn to the ON or RUN position. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.
Using the Safety (Red Handled) Control Switch	The safety (red handled) control switch allows you to temporarily disable the remote vehicle starter feature, this is especially helpful when having your vehicle serviced or valet parked. To disable the remote start: Move the safety (red handled) control switch to the OFF position.
Preheating or Precooling the Vehicle's Interior	Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioning will activate and heat or cool the vehicle’s interior to your setting.
Turning on the Rear Window Defroster (Optional)	While the vehicle is running via remote vehicle start, press and hold the OPT button on the remote control for 2 seconds. The rear window defroster will turn on for 10 minutes or the vehicles preset time limit.
Using the "Quick-Stop" Feature	If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage quick stop: Stop the vehicle and place the transmission in PARK. With your foot off the brake pedal, press and release the OPT button on the remote control two (2) times within 2 seconds. The parking lights will turn on indicating the vehicle is now running via remote vehicle start. Remove the keys from the ignition and exit the vehicle. Press the LOCK icon button on the remote control to lock the vehicle’s doors if desired. Note: Do not leave children or animals unattended in the vehicle when using the quick-stop feature.
Operating the 2 or 4 Hour Start Up Timer Mode	The system has the ability to start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if is garaged. Selecting between 2 and 4 hour start up: (default 4 hour) Begin with the safety (red handled) control switch in the ON position. Turn the ignition switch ON then OFF. Within 10 seconds move the safety (red handled) control switch OFF, ON, OFF, ON (2 switch cycles) to select a 2 hour start timer. After 10 seconds the parking lights will flash and the system will sound 2 times indicating that the 2 hour start timer is selected. Or Within 10 seconds move the safety (red handled) control switch OFF, ON, OFF, ON, OFF, ON, OFF, ON (4 switch cycles) to select a 2 hour start timer. After 10 seconds the parking lights will flash and the system will sound 4 times indicating that the 4 hour start timer is selected. To begin the 2 / 4 hour start up timer mode: Turn the ignition key ON then OFF. Within 10 seconds press the OPT button on the remote control four (4) times. The parking lights will flash and the system will sound 4 times indicating the 2 / 4 hour start up timer mode has been activated. The vehicle will start every 2 or 4 hours and run for the preset time limit (5, 10, 15 or 20 minutes) and then shutdown. This will continue for 48 hours unless the 2 / 4 hour start up timer is cancelled. To begin the 2 / 4 hour start up timer mode from the remote control: Activate the remote vehicle start feature using the remote control. Shutdown the remote vehicle starter using the remote control (press the OPT button 2 times). Within 10 seconds press OPT button on the remote control 4 times. The parking lights will flash and the system will sound 4 times indicating the 2 / 4 hour start up timer mode has been activated. The vehicle will start every 2 or 4 hours and run for the preset time limit (5, 10, 15 or 20 minutes) and then shutdown. This will continue for 48 hours unless the 2 / 4 hour start up timer is cancelled. To cancel the 2 /4 hour start up timer mode: Start the vehicle using the ignition key, then press the brake pedal. Or Activate the remote vehicle start feature using the remote control.
Operating the Temperature Start Mode	The system has the ability to start the vehicle when the temperature reaches 0 degrees. To toggle this feature on/off using the remote control: Press the UNLOCK and OPT buttons simultaneously for 1 second. Note: This feature must be turned ON in Options programming. Check with your installing dealer to insure this feature is set to the ON position.
Operating the Daily Start Timer	The system has the ability to start your vehicle based on a 24-hour countdown timer. To activate this feature, using the remote control: Press the LOCK and OPT buttons simultaneously for 1 second. The system will begin counting down from 24 hours, and start the vehicle when it reaches zero. This timer will only activate 1 time and will need to be reactivated for each 24 hour period.
Remote Start Safety Features	For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur: The vehicle hood is open. The brake pedal is pressed prior to turning the ignition key to the ON position. The engine reaches 3 times its normal idle speed. The safety (red handled) control switch is turned to the OFF position.
Using Valet Mode	To engage valet mode: Turn the ignition key to the ON position. Press and hold the emergency override button. The blue dashboard mounted LED will light solid indicating that the system is in valet mode. When valet mode is activated the dash mounted status LED will light solid, and all security functions will be disabled. To disengage valet Mode: Turn the ignition key to the ON position. Press and release the emergency override button. The blue dashboard mounted LED will turn off indicating that the system has exited valet mode. When the valet mode has been deactivated the dash mounted status LED will turn off and all security functions will be enabled the next time the system is armed.
Using the Optional Turbo Timer Feature	To engage the turbo timer feature: With the vehicle running via the ignition key, and your foot off of the brake pedal. Engage the vehicle’s parking brake. The vehicle’s parking lights will turn on to verify the turbo timer feature has been activated. Turn the ignition key OFF, the vehicle will continue to run for an additional 5 minutes. To disengage the turbo timer feature: Press the vehicle’s brake pedal. Or Turn the safety (red handled) control switch to the OFF position.
Emergency Override Procedure	If your transmitter is lost or disabled, it will be necessary use the emergency override button to turn the security system off. There are two types of emergency override procedures. Check with your installing dealer to find out what has been activated on your system. Standard Emergency Override Procedure: Enter the vehicle (the security system will trigger. Turn the ignition key to the ON position. Press and release the emergency override button (The security system will turn off). Note: If the automatic arming feature is enabled on your system. The security system will re-arm the next time the ignition key is turn off and the vehicle’s doors are closed. Coded Override Procedure: The system has an optional override mode that allows you to program a 2-digit personal code using the emergency override button offering a higher level of security. This feature must be enabled by your installing dealer, the default override code is 11. Enter the vehicle (the security system will trigger). Turn the ignition switch to the ON position. Within 5 seconds press the emergency override button the number of times corresponding to the first digit of your personal code (Default digit is 1). Within 5 seconds turn the ignition key OFF, then ON. Within 5 seconds press the emergency override button the number of times corresponding to the second digit of your personal code (Default digit is 1). Within 5 seconds turn the ignition key OFF, then ON. If entered correctly the security system will turn off. Turn the ignition key to the OFF position. Programming Your Personal Override Code: Make sure the security system is disarmed. Turn the ignition key to the ON position. Within 10 seconds press and release the override button 3 times. Within 10 seconds turn the ignition key OFF then ON 3 times (The horn will honk and the lights will flash 1 time). Within 10 seconds press and release the override button the number of times corresponding with the first digit of your personal code (1-9). Within 10 seconds turn the ignition key OFF then ON. Within 10 seconds press and release the override button the number of times corresponding with the second digit of you personal code (1-9). Within 5 seconds turn the ignition key OFF. You will notice the LED flash a number of times corresponding with the code you entered. Note: If 15 seconds of inactivity pass the system will abort programming. Note: Do not lose your “Personal Override Code”. Reprogramming a new code without the original code can only be performed by an authorized dealer.

For more information, please refer to your Owner's Manual.