Operating Instructions for PRO9276XR Remote Start System

Operating Instructions for PRO9276XR Remote Start System
Keyless Entry	To lock your vehicle: Exit the vehicle.  Close all doors, the hood and the trunk. Press the lock button of your key chain transmitter. As a keyless entry unit, for your convenience, the parking lights will flash once when the doors are locked and twice when the doors are unlocked. If the optional illuminated entry feature has been added, the interior light will turn on when the doors are unlocked and remain on for 30 seconds or until the ignition is turned on. Holding the lock/unlock transmitter button for 3 seconds will activate the car finder mode causing the parking lights to flash and the optional horn to beep for 30 seconds or until the ignition is activated again for 3 seconds or any other button is operated. Note: This system has the ability to unlock the drivers door with the first press of the unlock transmitter button and then unlock all other doors when the unlock button is pressed a second time. This optional feature may require additional components. Consult your installation center to determine if this feature has been added to your vehicle. Additionally, this system can be programmed to automatically lock and unlock the doors with the turning on and off of the ignition key.
Additional  Remote Function (Channel 3)	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Closure Remote Garage Door Interface To activate the optional accessory, press and hold the Trunk/Key button on the key chain transmitter for 4 seconds. Note: The feature that has been added to channel 3 will always be activated using the same transmitter button that remotely starts the vehicle. There is no way to move the channel 3 function to a different transmitter button. Note: If your system utilizes the transmitter shown, the second option button may be configured to operate additional accessories. Please consult your installing retailer for more information concerning the options available.
Additional  Remote Function (Channel 4)	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Can be set up to activate Rear Window Defogger during remote start if vehicle is so equipped. Remote Window Closure Rear Hatch Release Right or Left Slider doors in an equipped van To activate the optional accessory, press the option button on the key chain transmitter. The optional accessory will immediately engage. Note: If your system utilizes the transmitter shown, the second option button may be configured to operate additional accessories. Please consult your installing retailer for more information concerning the options available.
Additional  Remote Function (Channel 5)	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Closure Rear Hatch Release Right or Left Slider Doors in an equipped van To activate the optional accessory, press the option button on the key chain transmitter. The optional accessory will immediately engage. Note: If your system utilizes the transmitter shown, the second option button may be configured to operate additional accessories. Please consult your installing retailer for more information concerning the options available.
Additional  Remote Function (Channel 6)	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Hatch Release Right or Left Slider doors in an equipped van Driver Priority Settings in vehicles so equipped To activate the optional accessory, press the option button on the key chain transmitter. The optional accessory will immediately engage. Note: If your system utilizes the transmitter shown, the second option button may be configured to operate additional accessories. Please consult your installing retailer for more information concerning the options available.
Additional  Remote Function (Channel 7)	This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Rear Hatch Release Right or Left Slider doors in an equipped van Driver Priority Settings in vehicles so equipped Second Driver Priority Settings in vehicles so equipped To activate the optional accessory, press the option button on the key chain transmitter. The optional accessory will immediately engage. Note: If your system utilizes the transmitter shown, the second option button may be configured to operate additional accessories. Please consult your installing retailer for more information concerning the options available.
PRLED Safety Control Switch	The Pushbutton LED control switch allows you to temporarily disable the remote starting function of the system. This is recommended whenever the vehicle is being serviced. To place the system in service mode:  With the system disarmed/unlocked, and the ignition switch off, press and hold the PRLED on. Turn the ignition switch on, off, on, off, on, off. The LED begins to flash two short flashes followed by one long flash and continues this pattern until returned to normal mode of operation. This puts the unit into the R/S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise. To exit R/S Override Mode: With the system disarmed, press and hold the PRLED on. Turn the ignition switch on, off, on, off, on, off. The LED turns off indicating that the R/S unit is fully functional once again.
Turbo Timer Mode	This system provides a means to cool down the vehicles turbo charger, if so equipped, by allowing the vehicle to continue to run for a prescribed period of time every time the vehicle's engine is turned off. This feature requires the system to be set up for turbo timer during installation. Consult with your installation center to be certain this feature was activated and how long the vehicle will continue to run, 3, 5, or 10 minutes after the ignition switch is turned off. To activate the turbo timer, anytime the engine is running for more than 15 seconds: Place the gear selector in park. Set the parking, (hand), brake. Be certain your foot is off the brake pedal. Press the program/Push-Button switch 2 times within 5 seconds. The parking lights will flash two times indicating the mode was successfully entered. If your parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle's brake, or release the parking brake, or activate the transmitter's start button two times in succession. Any of these will cause the engine to turn off.
Remote Starting the Vehicle	The system will not start the vehicle if any one of the following situations exists: The vehicle's hood is opened. The gear selector is not in Park. The brake pedal is depressed. The system is in the remote start override mode. CAUTION: Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if the car is garaged. To remote start the vehicle: Press and release the transmitter button with the Trunk/Key symbol on it two times within 2 seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15 or 20 minute run cycle. As a visual indication, the parking lights will flash or remain on depending on the setting by your installation center. When you arrive at the vehicle, unlock it with the key or by pressing and releasing the unlock button of your key chain transmitter. Enter the vehicle and turn the ignition key to the on position. Step on the brake pedal to disengage the remote start unit. The vehicle will continue to run but now on it's own power. CAUTION: Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. Note: The engine will stop running before the pre-programmed run cycle has expired if you perform any one of the following functions: Press and release the Trunk/Key button on the key chain transmitter two times within 2 seconds. Depress the brake pedal. Open the vehicle's hood Place the system in the remote start override mode. Race the engine to above 4000 RPM.
Operating on Automatic Start Up Timer Mode	The system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. CAUTION: Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if the car is garaged. To Begin the Automatic Start Up Timer: Turn the ignition key on then off. Within 10 seconds, activate the RF start command two times. (Push the second channel button of your key chain transmitter 4 times). The parking lights will flash 4 times indicating the timed start mode is activated. The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-programmed time (5, 10, 15 or 20 minutes), and then shut off. This will continue for 48 hours. Note: The automatic start up timer can also be initiated from the key chain transmitter. To do this: Start the vehicle using the key chain transmitter by pressing and releasing the trunk/key button 2 times. Shut off the vehicle using the key chain transmitter by pressing and releasing the trunk/key transmitter button 2 times. Within 10 seconds, activate the RF start command 2 times. (Press the trunk/key button four times). The lights will flash 4 times to indicate timed start mode has been initiated.  To cancel the automatic start up timer do one of the following: Start the vehicle manually with the use of the ignition key and depress the brake pedal. Remote start the vehicle using your key chain RF transmitter. Shut off the vehicle using the key chain transmitter by pressing and releasing the trunk/key transmitter button 2 times.
Telematic Upgrade	This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that can give you control of certain functions of your vehicle from a Telephone, or in some cases a computer interface. Please check with your installation center for the most recent Telematic Upgrades. If you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide an operators manual advising you of the features of the system and means available to control these features on your vehicle.

For more detailed operating instructions, please refer to your Owner's Manual.

Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.

Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.

NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.