|
Remote Operation for the Code Alarm Elite 4500 Alarm |
|||||||||||
|
System Operation Arming the Security System:
Disarming the Security System: Press the "DISARM" button on the remote control transmitter. The siren will emit one long chirp and the parking lights will flash one time to indicate the system is disarmed. If the siren sounds four short chirps, the alarm has sounded while you where away. The system will rearm in one minute unless the ignition is turned on or the system is placed in the valet mode. Remote Control Panic Alarm: When activated the remote control panic alarm will sound the siren continuously and flash the parking lights for 30 seconds. To activate the panic alarm, press the button(s) indicated on the remote control transmitter operating instruction card. The panic alarm can be shut off by pressing any button on the remote control transmitter. The panic alarm can be activated when the security system is armed or disarmed. |
|||||||||||
|
System Components Valet Switch: The valet switch is used for turning the valet mode on and off. Valet mode prevents the security system from arming, yet allows the convenience functions (door lock & unlock, etc.) to operate normally. Valet mode is useful when valet parking, fueling or servicing your vehicle. To use the valet mode, disarm the security system and toggle the valet switch to the on position. The status indicator will begin blinking in a double flash pattern to confirm security system is in valet mode. To re-enter the normal operating mode, toggle the valet switch to the off position. The status indicator will turn off, indicating the system is now in the normal operating mode. Turn the ignition ON then OFF to reset the automatic arming timer or arm the system using the remote control transmitter. Override/Programming Button: The Override/Programming button is a hidden push button switch that can be used to disarm the security system if your remote control transmitter is lost or stolen. However, the override/programming button is more commonly used for programming new remote control transmitters to the system. To prevent unauthorized use of the override/programming button, the ignition key is also needed to disarm the system or program transmitters.
Visual Alarm Status Indicator: The visual alarm status indicator is a high intensity red blinking light. The status indicator, mounted in a location visible from the outside of the vehicle, displays the security system's status while creating a powerful theft deterrent. The chart below shows the different status indications and their meanings.
|
|||||||||||
|
Security Features When the security system is armed:
When the alarm is sounding the following events occur:
Shock Sensor: The shock sensor is designed to detect impacts to the body of the vehicle. The force of impact required to "trip" the shock sensor is adjustable by your Installer. At the time of installation, your Installer will set the shock sensor threshold to a medium level. Should you want to change the shock sensors threshold level, contact your dealer - they can adjust the shock sensor to your desired setting. When the system is armed, the shock sensor continually monitors for impact to the body of the vehicle. An impact of greater magnitude than the threshold setting will trigger a full alarm cycle.
Armed Output (Optional): The armed output can be used to activate other accessories or to control a second interrupt circuit to enhance the security system's effectiveness. Arming Delay: You may notice that for a short period of time after you arm your security system, it doesn't seem to respond to any trip inputs, such as opening a door or slapping a side window. This is because the system ignores all sensors and inputs for 5 seconds after the second "arm" chirp. The system does this to prevent any false alarms that could occur from a sensor being tripped at the same time that the system is armed. Arming the System when a Protected Entry Point is Open: When there is a protected entry point open at the time that the system attempts to arm, the siren will chirp and the parking lights will flash one time. The system will then wait, in a pre-armed state, until the protected entry point is closed. After the entry point has been closed, the siren will chirp and the parking lights will flash again, this time indicating that the system is armed. If 4-1/2 minutes passes and the entry point is still opened, the system will arm bypassing the open entry point. The entry point will then be bypassed until the system is disarmed and rearmed. Disarming the Security System After the Alarm has been Tripped: If an alarm has been tripped while you were away, the siren will emit four short chirps when the system is disarmed instead of the one normal disarm chirp. In addition to the siren chirps the status indicator will be flashing rapidly to indicate that the alarm has been tripped, the status indicator will continue flashing rapidly until the system is rearmed or the ignition key is turned on. The Trip ID feature below can be used to determine how the alarm cycle was triggered. Trip ID: When the status indicator is flashing rapidly, the Trip ID feature will indicate how the previous alarm cycle was triggered.
|
|||||||||||
|
Remote Controlled Convenience Functions The remote controlled convenience functions described in this section and the personal safety features described below, may require additional parts and labor to be hooked up. Because additional parts and labor may be required, these features are referred to as optional features. Some features listed below are only available on certain systems, see your dealer for details. Remote Controlled Door Lock and Unlock: When the system is armed by remote control the system will lock the doors when the siren chirps the first time. The doors will be unlocked when the system is disarmed.
Trunk Release: Press the button for trunk release on the remote control transmitter. If the security system is armed when the trunk release output is activated, the security system will be disarmed and the doors unlocked. If you are going to leave the vehicle unattended, remember to rearm the security system with the remote-control transmitter. When the ignition key is on, the trunk release output is disabled to prevent the trunk or hatch from being opened while driving.
Car start output (Systems with two button remote controls): The car start output is activated by pressing the "START" button on the remote control for two (2) seconds. When activated the system will lock the doors and trigger the CSM-2 remote controlled car starter (not included). Auxiliary outputs (Systems with four button remote controls): Auxiliary outputs are activated by pressing the appropriate button on the remote control transmitter. Auxiliary outputs will remain active as long as the button on the remote control transmitter is pressed, up to 10 seconds. Auxiliary outputs can be activated when the security system is armed or disarmed. When an auxiliary output is activated while the security system is armed, the sensor inputs are bypassed, during the auxiliary output operation, to prevent security system from being triggered. |
|||||||||||
|
Personal Safety Features Illuminated Entry/Exit: When disarmed, the security system will turn on the Interior dome light to illuminate your entry into the vehicle. The dome light will stay on for one minute, until the vehicle is started or the security system is rearmed. Additionally, when the ignition key is turned to off the system will turn the interior dome light on, providing an illuminated exit from the vehicle. The dome light will turn off after one minute or when the system is armed. Automatic Door Lock and Unlock: If all protected openings are closed when the ignition key is turned to the on position, the security system will lock the doors. When the key is turned back off, the system will unlock the doors to allow an easy exit from the vehicle. |
|||||||||||
|
Other Useful Information Low Vehicle Battery?
System Maintenance: Your security system does not require any specific maintenance except for occasionally changing transmitter batteries. However, it is suggested that the system be armed and all protected zones should be checked on regular basis to make sure that they trigger an alarm cycle. Should the system malfunction In any way, contact your dealer as soon as possible for service. Programmable operating characteristics: Many of the security system's operating characteristics can be programmed by your installer to operate differently, see your security dealer for additional details. About transmitter range... The receiver inside your vehicle security system and the remote control transmitter are designed together to have an effective operating range of up to 100 feet during normal conditions. Although at times you will experience range greater than that, there are certain conditions that will cause the effective transmitter range to be less than you would normally experience. Atmospheric conditions and radio interference are just a few examples of the types of interference that can reduce transmitter range. |
|||||||||||
Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.
Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.
NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.
Comments
0 comments
Article is closed for comments.