Operating the Code Alarm PRO200 Keyless Entry Upgrade

Remote Operation for the Code Alarm PRO200 Keyless Entry Upgrade 

ARMING THE SYSTEM: (ACTIVE)

1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren will chirp one time, the parking lamps will flash one time, and the red dash mounted L.E.D. will begin to slowly flash, indicating that the system is ARMED.

ARMING THE SYSTEM: (PASSIVE):

1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash mounted L.E.D. will begin to flash rapidly, indicating that the system is automatically ( passively) arming. As an added convenience, the 30 second automatic passive arming will not begin until all doors are closed, allowing passengers to exit the vehicle at their convenience.
3. In 30 seconds, you will hear a single short chip from the siren, and the vehicle's parking lamps will flash one time, indicating that the system has ARMED. At this time, the red dash mounted L.E.D. will begin to flash slowly, providing a visual indication that the system is fully armed.
4. In many cases, when the alarm is allowed to automatically passive arm, there will be a 15 second delay after a door is opened before the alarm will sound. However, if the system is programmed for instant trigger there will be no delay. Check with your installer.

IMPORTANT! When the system is programmed for passive arming, the system will always arm, even when the keychain transmitter has not been used to lock the doors. When you leave the vehicle, and a door has been left opened, the system will arm after 1 0 minutes. If you plan to vacuum the car, or if service work is being performed, either leave the key in the ignition and switched to the on position, or put the system into valet mode. If you do not do this, the system will arm in 10 minutes, and you will probably inadvertently trip the alarm.

PROTECTION WHILE THE SYSTEM IS ARMED:

• Opening any door, hood, or trunk will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and automatically re-arm the vehicle. If the potential thief left a door opened, the alarm will sound for five more 30 second cycles, then re - arm and ignore the opened door zone.
• Whenever the system is armed, the red dash mounted L.E.D. indicator will slowly flash. This serves as a visual deterrent to the potential thief. The L.E.D. is a very low current bulb, and will not cause the vehicle's battery to drain, even when the vehicle is left unattended for extended periods.
• Whenever the system is triggered, the vehicle's parking lights will flash for the 30 second alarm cycle, attracting added visual attention to the vehicle.
• Whenever the system is armed, the vehicle's starter will be by - passed. The vehicle will not start.

DISARMING THE SYSTEM:

1. As you approach the vehicle, press and release the unlock button on the keychain transmitter.
2. The siren will chirp two times, the parking lamps will flash two times, and the red dash mounted L.E.D. will turn off, indicating that the system is DISARMED. If the optional entry illumination feature has been installed, the vehicle's interior lights will turn on for 30 seconds, or until the ignition key is turned on. NOTE: If your system has been programmed for" passive arming ", then it will begin to re - arm immediately after disarming. This is indicated by a rapid flashing of the red dash mounted L.E.D. Opening one of the vehicle's doors will suspend the passive arming process until all doors have been closed, or until the ignition key has been turned on.

INTRUSION WARNING SIGNALS: The system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp four times when the system is disarmed. The vehicle's parking lights will also flash three times to indicate an intrusion has occurred. Enter the vehicle and observe the dash mounted L.E.D. for further information.

1. If the L.E.D. is flashing one time ... pause ... one time ... pause ... etc., then an intrusion attempt was made to a voltage sensing, light activated entry point, or to an optional sensor that has been connected to zone 1.
2. If the L.E.D. is flashing two times ... pause ... two times ... pause ... etc., then an intrusion attempt was made to the hood or trunk, or to an optional sensor that has been connected to zone 2.
3. If the L.E.D. is flashing three times ... pause ... three times ... pause ... etc., then an intrusion attempt was made through one of the vehicle's doors. These intrusion warning indicators are stored in the system's memory, and will only be erased when the ignition key is turned to the" on " position.

OPERATING THE EMERGENCY PANIC: The buttons on your keychain transmitter will allow you to immediately activate the alarm in emergency situations. To use the remote panic switch:

1. Press the unlock, then lock, then unlock buttons on your keychain transmitter within 3 seconds. The alarm will immediately sound, and continue to sound for 30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press and release the unlock button on your keychain transmitter.

USING THE VALET SWITCH: The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. You should also use the valet switch if your system is programmed for passive arming, and you intend to vacuum or wash the vehicle. To use the valet mode:

1. Disarm the system, enter the vehicle, and turn the ignition key to the "on" position.
2. Move the valet toggle switch to the "on" position. The dash mounted L.E.D. will turn on solid, and remain on as long as the system is in valet mode. Turn ignition key off.
3. To return to normal operation, move the valet switch to the "off" position any time the ignition key is in the "on" position.

USING THE EMERGENCY OVERRIDE SWITCH: In the event you lose your keychain transmitter, or if the transmitter fails to unlock the doors and disarm the system, the emergency override switch can be used to disarm the system. To use the emergency override switch:

1. Open the door to gain access to the emergency override push-button switch. The alarm WILL SOUND.
2. Press and release the emergency override push-button switch. You now have 12 seconds in which to turn the ignition key to the "on" position.
3. Turn the ignition key to the "on" position. The alarm will disarm.

ADDITIONAL REMOTE FUNCTION: This system allows the control of optional Remote Car Starter PRO200. To operate the optional accessory:

1. Press the lock, then unlock, then lock buttons on your keychain transmitter within 3 seconds.
2. The optional accessory will immediately activate.

OPTIONAL AUTO LOCK/UNLOCK FEATURE: If your existing factory installed keyless entry system did not include the automatic door lock and unlock feature, then this feature can be activated from the PRO200 upgrade module. When this accessory has been added, any time the ignition key is turned to the on position and all vehicle doors are closed, the doors will lock in 4 seconds. Additionally, any time the ignition key is turned to the off position, the doors will unlock.

ELIMINATING THE ARM I DISARM CHIRPS: The normal arming and disarming confirmation chirps can easily be turned off using the valet toggle switch. To do this:

1. You must begin with the valet switch in the" off " position.
2. Turn the ignition key on. and then off.
3. Within 10 seconds of turning the ignition key off. move the valet toggle switch to the on - off - on - off - on - then off positions.
4. If. before proceeding with step 1. the chirps were on. then you will hear 2 chirps to indicate that the chirps have been turned off. If, before proceeding with step 1, the chirps were off, then you will hear 1 chirp to indicate that the chirps have been turned on.
5. Whenever power to the system has been disconnected ( for repair or service to the vehicle ). the chirps will be activated when the power is re - connected. To turn the chirps off. simply execute steps 1 through 3 above. NOTE: Whenever the Arm/Disarm chirps are by-passed, the 3 chirp defective zone and the 4 chirp intrusion indicator will always operate. This feature will always warn you if a door was left ajar when arming. or the vehicle was tampered with in your absence.

Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.

Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.

NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.