Operating the Code Alarm CA410 Remote Start Upgrade

Operating the Code Alarm CA410 Remote Start Upgrade

This Remote Start Upgrade system can be wired to operate from any unused button(s) from your transmitter. Please check with your installing dealer for which transmitter button is connected to your remote start system, and if you require a single, double, or sequential press of the button(s) to operate your system.

SAFETY (Red Handled ) CONTROL SWITCH: The control switch allows you to temporarily disable the remote starting function of your Remote Start system. To disable the unit, move the red handled control switch to the OFF position.

REMOTE STARTING THE VEHICLE: The system WILL NOT start the vehicle if any one of the following conditions exist:

• The vehicle's hood Is opened.
• The gear shift selector is in any gear other than park.
• The brake is depressed.
• The safety control switch is in the OFF position. CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if the car is garaged.

Remote Starting The Vehicle: Press and release the proper button or combination of buttons on your transmitter to activate the remote start system. The vehicle will start and remain running for the pre-programmed 10 or 15 minutes. As a visual indication, the parking lights will flash or turn on depending on the programming set up by your installation center. When you arrive at your vehicle, unlock the vehicle by pressing and releasing the unlock button of your keychain transmitter or by use of the vehicle key. Enter the vehicle and turn the ignition key to the ON position. CAUTION! Do not turn the key to the start position. This will cause the starter motor to engage with the running engine which could result in damage. Step on the brake pedal to disengage the remote start unit. The vehicle will continue to run on it's own power.

NOTE: The engine will stop running before the expiration of the pre-programmed run timer if you complete any of the following:

• Pressing the proper button or buttons of your transmitter while running under control of the remote start system will turn the vehicle off.
• Depress the vehicle's brake pedal.
• Open the hood.
• Move the red handled control switch to the OFF position.
• Race the engine to above 4000 RPM.

OPERATING ON AUTOMATIC START TIMER MODE: The system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine.

TO BEGIN THE AUTOMATIC START TIMER:

1. Start the vehicle using the transmitter by pressing and releasing the remote start transmitter button(s).
2. Shut off the vehicle using the transmitter by pressing and releasing the remote start transmitter button(s).
3. Within 10 seconds of step 2, activate the remote start 2 times. The parking lights will flash 4 times indicating the timed start mode is activated.

ADJUSTING THE START TIMER FROM 2 TO 4 HOURS: The SAFETY (Red Handled ) CONTROL SWITCH also allows you to select between automatic 2 hour start or 4 hour start when using the automatic start timer mode. The factory preset start up time for this mode is every 4 hours. To select between 2 or 4 hour start timer:

1. Begin with the safety control switch in the ON position.
2. Turn the ignition switch ON then OFF.
3. Within 10 seconds, move the control switch OFF,ON,OFF,ON(2 switch cycles) to select a 2 hour start timer. After 10 seconds expire, the parking lights will flash 2 times confirming that the 2 hour start cycle is set. Or, within 10 seconds move the control switch OFF,ON,OFF,ON,OFF,ON,OFF,ON (4 switch cycles) to select a 4 hour start timer. The parking lights will flash 4 times confirming that the 4 hour start timer is set.

CANCELING THE AUTOMATIC START TIMER: To cancel the automatic start timer do one of the following:

• Start the vehicle using the ignition key and depress the brake pedal.
• Remote start & stop the vehicle using your transmitter.