Operating the Code Alarm F30 Keyless Entry Upgrade

Operating the Code Alarm F30 Keyless Entry Upgrade

Using Your Existing Remote Transmitter

Arming the Security System: To arm the system, exit the vehicle, close all doors, then press the LOCK button on your OEM Keyless Entry Remote Control. The horn will “chirp” twice and the parking lights will flash twice, indicating the system is armed. The status indicator (red warning light on the dash) will blink steadily, once per second.

Pre-arm Mode: If the horn chirps and the parking lights flash only once, this indicates that the vehicle courtesy light is on, or that an entrance is not closed securely. Check to see that doors, hood, and trunk are properly closed. Once all entrances are secured (and the courtesy light is off), the system will chirp / flash again. The system is now fully armed. (If the entrance is not secured within 4 minutes, the system will arm and ignore the unsecured entrance until it is closed.)

Disarming the Security System: To disarm the system, press the UNLOCK button on your OEM Keyless Entry Remote Control. The siren will chirp and the parking lights will flash once.

Attempted Intrusion Identification: If the horn chirps four times when disarming, this indicates that the system was triggered in your absence. The status indicator will also flash rapidly. Perform the following operation to determine the protected zone that triggered the system: After disarming, press the emergency override button. The siren will chirp to indicate the cause of the alarm trigger: 1 chirp = IT-s Interior Theft Sensor, 2 chirps = Door, 3 chirps = Hood, 4 chirps = Trunk/Optional Sensors, 5 chirps = Ignition was turned on.

To enter valet mode: With the key, turn the ignition on, then turn off 3 times within 5 seconds.

To exit Valet mode: With the key, turn the ignition on, then turn off 3 times within 5 seconds.

When Your Security System is Triggered

The F30 will trigger if one of the following events occurs while the system is armed:

• Any protected entrance is opened
• The vehicle ignition is turned on
• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the siren (or horn) sounds and the vehicle parking lights flash for 30 seconds. The system will then rearm, awaiting the next intrusion attempt.

To stop the siren while keeping the alarm armed and doors locked: press the LOCK button (on the OEM Keyless Entry Remote) while the system is triggered.

The Interior Status Indicator

The Status Indicator is a high-intensity red light mounted in a visible location on the vehicle dashboard. This red light gives a visual indication of the alarm system’s state of operation. Note the chart below:

Emergency Disarm Procedure

If your remote control is lost or fails to function, use this procedure to disarm the F30 and start your vehicle:

1. Use the keys to enter the vehicle. The alarm will sound once the door is opened.
2. Insert the key into the ignition and turn to the ON position.
3. Locate and press the emergency override button. The alarm will turn off and then you will be able to start your vehicle.

Programming Selectable Options

Programming Selectable Options using a generic Code Alarm remote.

Programming the Remote Transmitter:

1. Open the driver’s door.
2. Turn vehicle ignition on.
3. Press and hold emergency override button. After 15 seconds, the siren or horn will sound three (3) times. This indicates that the unit has entered the transmitter programming mode.
4. Release the button.
5. Press the Arm button on the remote transmitter to be programmed. The siren or horn will sound once, indicating that the system has “learned” that remote transmitter.

Programming Options:

1. Repeat steps 1-4 of Programming the Remote Transmitter
2. Press and release the emergency override button. The horn or siren will sound four (4) times. This indicates that the unit has entered the Keyless Options Programming mode.
3. Press the FIND/PANIC button to advance to the next feature. The siren or horn will sound a number of times to indicate the number of the option.
4. Press the ARM button to turn the option on or off. The vehicle status indicator on the dashboard indicates whether an option is on or off. If the selected option is ON, the indicator will light. If the selected option is OFF, the indicator will turn off. The status indicator will turn on or off when an option is changed.
5. When changes are complete, press and release the emergency override button to continue to the next option bank. (Siren or horn will sound five (5) times.)
6. To reset all options back to factory defaults, press the DISARM button. Note: Option Bank Installer options will never reset.
7. Turn ignition off to exit programming.

Note: The following section describes programming options without using a remote transmitter. This programming method can be used for all options programming with the exception of IT-s sensor sensitivity adjustments. When adjusting the IT-s sensor a programmed remote must be used.

Alternative Method for Programming Selectable Option’s:

1. Open the driver’s door.
2. Turn vehicle ignition on.
3. Press and hold emergency override button. After 15 seconds, the horn will chirp three (3) times. This indicates that the unit has entered the transmitter programming mode.
4. Release, then press and release the button, again. The horn will chirp (4) times indicating the unit has entered the programming options mode.
5. Press vehicle’s lock switch to advance to the next feature. The siren or horn will sound a number of times to indicate the number of the option.
6. Press vehicle’s unlock switch to turn the option on or off. The vehicle. The vehicle status indicator on the dashboard indicates whether an option is on or off. If the selected option is ON, the indicator will light. If the selected option is OFF, the indicator will turn off. The status indicator will turn on or off when an option is changed.

Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.

Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.

NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.