Operating the Code Alarm PC6100 or ELITE6100 Keyless Entry System

Operating the Code Alarm PC6100 or ELITE6100 Keyless Entry System

Using Your Remote Transmitter

Locking the Vehicle Doors: To lock the vehicle doors, exit the vehicle, close all doors, then press the LOCK button. The horn will “honk” twice and the parking lights will flash twice, indicating the system is locked and the starter disable is armed. The status indicator (red warning light on the dash) will blink steadily, once per second, if equipped.

Unlocking the Vehicle Doors: To unlock the system, press the UNLOCK button. The horn will “honk” and the parking lights will flash once, and the doors will unlock. The courtesy light will turn on for 1 minute, or until the vehicle is started, and the starter disable will turn off.

Two-Stage Door Unlock: If this feature is enabled on your system, pressing UNLOCK one time will unlock only the driver’s door. Press UNLOCK again within 1 minute to unlock all doors.

Activating the Trunk Release Feature: Press and hold TRUNK to open the vehicle trunk or hatch (if equipped and connected). If this button is used to operate another accessory, the accessory will stay active for as long as the button is held.

Using the Auxiliary Function: Press and hold the LOCK button to turn on the Auxiliary Function (if enabled).

Using the Progressive Car Finder Feature: Press FIND on the remote control to locate your vehicle. The horn will emit five short “honks” at low volume, increasing in volume each of three times the button is pressed.

Personal Protection Alarm (Panic): Press and hold the PANIC button to activate the vehicle horn and parking lights for 30 seconds. (If the vehicle horn is connected, the horn will “honk” for 30 seconds.) Press any remote control button to turn off the Panic alarm.

Using Second Car Mode: If this feature is enabled, one transmitter will control two vehicles equipped with a Power Elite system. To operate the second vehicle, press the shift button, then within two seconds, press the desired function button.

Automatic Convenience Options

The Power Code PC 6100 performs a variety of automatic functions to enhance security and comfort. Some of these features are programmable at the time of installation. Please see your installer for further details.

• Illuminated Entry: When the alarm system is disarmed, the vehicle courtesy lights will turn on for 1 minute, or until the vehicle is started or the system is re-armed.
• Illuminated Exit: When removing the key from the ignition, the vehicle courtesy lights will turn on for 1 minute, or until the Power Code PC 6100 is armed.
• Automatic Arming: The Power Code PC 6100 Starter Interrupt will arm automatically one minute after the key is removed from the ignition (if enabled). This feature can be temporarily disabled by placing the system into Valet mode.
• Ignition Lock: If all doors are closed and the vehicle is started with the key, the doors will automatically lock.
• Ignition Unlock: When removing the key from the ignition, the doors will automatically unlock.

System Maintenance

Changing the Remote Control Battery: The two 3-v lithium batteries (CR2016) supplied in your remote control should last approximately one year, depending on usage. When the battery begins to weaken, you will notice a decrease in range, or the distance from your vehicle that your remote transmitter will operate. Follow the instructions below to change the remote transmitter battery.

1. Insert the edge of a coin into the slot at the top of the remote control. Twist the coin to pry the remote control halves apart.
2. Remove the old batteries and replace with new ones. Be sure to observe the (+) and (-) signs in the battery compartment.
3. Carefully snap the case halves back together, then test the remote control.

Adding Remote Controls to Your System: The Power Code PC 6100 has the ability to operate from up to four (4) remote controls. Follow these instructions to add a remote control to your system.

1. Make sure the system is disarmed and the ignition is off.
2. Open the driver’s door.
3. Turn vehicle ignition on.
4. Press and hold emergency override button. After 15 seconds, the horn will sound three (3) times. This indicates that the unit has entered the remote control programming mode.
5. Release the button.
6. Press the LOCK button (button 1) on the remote control to be programmed. The horn will sound once, indicating that the system has “learned” that remote control.
7. Repeat step 6 for any additional remote controls.
8. Turn the vehicle ignition off to exit the programming mode. Test all remote controls to ensure that they work properly.

Deleting Lost or Stolen Remote Controls from Your System: If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to remove the control code from your system.

1. Make sure that you have all remaining remote controls available.
2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls to Your System.
3. a. If you have only one remaining remote control, press the LOCK button on that remote control four (4) times, pausing at least 1 second between each press. Make sure that the horn “honks” each time you press the LOCK button.
   b. If you have two remaining remote controls, press the LOCK button on each remote control two (2) times, pausing at least 1 second between each press. Make sure that the horn “honks” each time you press the LOCK button.
   c. If you have three remaining remote controls, press the LOCK button on the two remote controls one (1) time, then press the LOCK button on the remaining remote control twice. Pause at least 1 second in between each press. The horn must “honk” each time you press the LOCK button.
4. Turn the vehicle ignition off to exit the programming mode. When you are finished, the lost or stolen remote control will no longer operate your system.

Emergency Disarm Procedure

If your remote control is lost or fails to function, use this procedure to disarm the Power Code PC 6100 and start your vehicle.

1. Use the keys to enter the vehicle. The alarm will sound once the door is opened.
2. Insert the key into the ignition and turn to the ON position.
3. Locate and press the emergency override button. The alarm will turn off and then you will be able to start your vehicle.

Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.

Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.

NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.