Remote Operation for the Code Alarm CA1150 Security and Keyless Entry System

Remote Operation for the Code Alarm CA1150 Security and Keyless Entry System 

Using Your Remote Control

Arming the Security System: To arm the system, exit the vehicle, close all doors, then press the Lock button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second.

NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the Lock button to activate an audible arming response from the vehicle.

Bypassing The Shock Sensor: To arm the system and ignore the shock sensor press Lock button, then within 5 seconds press Lock + Alarm, the system will respond with 1 long chirp.

NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal operation the next time the system is armed.

Disarming the Security System: To disarm the system press the Unlock button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected).

NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the Unlock button to activate an audible arming response from the vehicle.

Two Stage Door Unlock (Optional): If this feature is enabled on your system, pressing the Unlock button one time will unlock only the driver’s door. Press Unlock again within 5 seconds to unlock the remaining doors.

Valet Mode:

To engage valet mode:

1. Turn the ignition key to the ON position.
2. Press and hold the emergency override button.
3. The LED will light solid indicating that the system is in valet mode.

When valet mode is activated the status LED will light solid, and all security and remote start functions will be disabled.

To disengage valet Mode:

1. Turn the ignition key to the ON position.
2. Press and release the emergency override button.
3. The LED will turn off indicating that the system has exited valet mode.

Activating the Trunk Release Feature (Optional): If this feature is enabled on your system, pressing and holding the Trunk button for 3 seconds will open the vehicle’s trunk or hatch.

Activating Optional AUX 1 (Optional): If this feature is enabled on your system, pressing the Lock and Unlock buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system.

Using the Progressive Car Finder Feature: Press the Alarm button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed.

Using the Personal Protection Alarm (Panic): Press and hold the Alarm button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s Lock and Unlock buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the Alarm button on the transmitter again for 3 seconds. The system will automatically stop after 30 seconds.

Car Jack Mode: This feature must be turned on in system programming, please consult your installing dealer. Triggering Car Jack mode: While the ignition is ON and press and hold Lock + Unlock for 2 seconds, the parking lights will flash 1 time and the system will act as follows:

1. 50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step.
2. Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing.
3. 90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 10 seconds.

LED and Siren/Horn Indications

Transmitter Button Functions

Replace Remote Control Batteries

1-Way 4 Button Remote Control: The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries:

1. Remove 3 screws and disassemble the halves of the remote control.
2. Remove the old batteries, observing the +/- symbols on the batteries and replace with new CR2016 batteries.
3. Reassemble the halves of the remote control and install the 3 screws.
4. Test operation of the remote control..