Functions and Indications on the Code Alarm CA6551SST Remote Start Security System Transmitter

Functions and Indications on the Code Alarm CA6551SST Remote Start Security System Transmitter 

Using Your Remote Control

Arming the Security System: To arm the system, exit the vehicle, close all doors, then press the Lock button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the Lock button to activate an audible arming response from the vehicle.

Passive Arming Bypass: If passive arming is enabled on your system, while the system is disarmed, press Unlock + Alarm, the system will respond with 1 chirp and the LED will turn on. The security system will remain in this temporally bypassed state for as long as you wish. To exit passive bypass, press the Lock or Unlock button and the system will return to normal status.

Bypassing The Shock Sensor: To arm the system and ignore the shock sensor press Lock, then within 5 seconds press Unlock + Alarm, the system will respond with 1 long chirp. NOTE: The system will only change the shock sensor setting for one arm cycle and will be defaulted back to normal operation the next time the system is armed.

Hidden Alarm Function: Press the Alarm button first, within 3 seconds press the Lock button to activate the hidden alarm function. The security system will arm with “Hidden Alarm Function” in which the siren / horn will be silenced if the system is triggered.

Disarming the Security System: To disarm the system press the Unlock button. The parking lights will flash 1 time, indicating the system is disarmed and has unlocked the doors (if equipped and connected). NOTE: The system is defaulted with Silent Choice enabled, which requires a second press of the Unlock button to activate an audible arming response from the vehicle. If your system is set up for 2 step unlock, a third press Unlock of will activate the audible response.

Two Stage Door Unlock (Optional): If this feature is enabled on your system, pressing the Unlock button one time will unlock only the driver’s door. Press Unlock again within three seconds to unlock the remaining doors.

Activating the Trunk Release Feature (Optional): If this feature is enabled on your system, pressing and holding the Unlock button for 3 seconds will open the vehicle’s trunk or hatch.

Activating Optional AUX 1 (Optional): If this feature is enabled on your system, pressing the Lock and Unlock buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system.

Using the Progressive Car Finder Feature: Press the Alarm button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed.

Using the Personal Protection Alarm (Panic): Press and hold the Alarm button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s Lock and Unlock buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the Alarm button on the transmitter again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed Transmitter Notification: As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.

Valet Mode: When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below:

1. Turn the vehicle’s ignition ON.
2. Push and hold the programming/valet button.
3. The LED will turn on solid when valet mode is active
4. Release the programming/valet button.

Eliminating Arm / Disarm Notification Chirps: System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.

1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.

Manually Overriding the Security System: Your system can be disarmed without the use of the transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system:

1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the ON position.
3. Within 10 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.

Car Jack Mode: This feature must be turned on in system programming, please consult your installing dealer.

Triggering Car Jack mode: While the ignition is ON and press and hold Lock + Unlock for 2 seconds, the parking lights will flash 1 time and the system will act as follows:

1. 50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode. If Car Jack mode is not turned off at this time it will advance to the next step.
2. Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing.
3. 90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CAR JACK MODE: Turn the ignition OFF then On and press the valet button within 10 seconds.

Using Your Remote Vehicle Starter

Remote Starting Your Vehicle: To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.

If your vehicle stalls or does not start, the system will pause 5 seconds, then try 2 more times to start the vehicle (a total of 3 attempts). The system will pause 5 seconds between each start attempt. If the vehicle does not start after the 3rd attempt, the system will abort the remote vehicle start process.

Remote Start Shutdown: Press and hold the Start button for 3 seconds to turn the vehicle off.

Entering the Vehicle while it is Running via Remote Vehicle Start:

1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN position.
4. Press the brake pedal. The remote vehicle starter will disengage and the vehicle will operate normally.

Preheating or Precooling the Vehicle’s interior: Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle’s interior to your setting.

User Programmable Run Time / Run Time Extension: The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes. Follow the steps below to extend the vehicle’s run time.

1. The remote start must already be active.
2. Press and release the button 4 times.
3. The system will chirp to confirm that the run time has been reset.

Using the “Quick-stop” Feature: If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you.

1. Stop the vehicle and place the transmission in PARK.
2. With your foot off the brake pedal, press and release the Start button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered.
3. Remove the keys from the ignition and exit the vehicle. Press the Lock button to lock the vehicle’s doors if desired. Note: Do not leave children or animals unattended in the vehicle when using the quick-stop feature.

Operating the 2 / 3 Hour Start Up Timer Mode: The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming.

WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start the vehicle if it is garaged.

To begin the 2 / 3 hour start up timer mode:

1. Turn the vehicle’s ignition ON then OFF.
2. Press and hold the valet button.
3. Press the Start button 4 times, the system will: (a.) When set for 3 Hour (default) - chirp 2 times and flash the parking lights 4 times. (b.) When set for 2 Hour - chirp 1 time and flash the parking lights 2 times.
4. Release the valet button.

To exit the 2 / 3 hour start up timer mode:

1. Turn the vehicle’s Ignition ON. OR
2. Activate the remote vehicle start feature using the remote control.

Turbo Timer: This option will keep the engine running to allow the vehicle’s turbo to properly cool down before shutting the engine off.

1. With the vehicle running via the ignition key and your foot off of the brake pedal.
2. Engage the vehicle’s parking brake and press the Unlock and Start buttons simultaneously.
3. The vehicle’s parking lights will turn on to verify the Turbo Timer feature has been activated.
4. Turn the ignition key OFF, the vehicle will continue to run until the preprogrammed time has elapsed (1, 3, or 5 minutes).
5. To disengage the turbo timer feature, press the vehicle’s brake pedal.

Operating the Daily Start Timer: The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the Lock & Start buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process.

1. Turn the ignition ON/OFF (vehicle must be disarmed).
2. Within 10 seconds, while pressing the brake, press and release the Start button twice.
3. The vehicle will emit 2 chirps.

Remote Start Safety Features: For safety and security reasons, the system will shutdown or prevent the remote vehicle starter from activating if any of the following occur:

1. The vehicle hood is open.
2. The brake pedal is pressed prior to turning the ignition key to the ON position.
3. The engine is over-revved (tach checking only).
4. Valet mode is active.

LED and Siren/Horn Indications

Additional 2-Way LCD Remote Control Functions

• Check Vehicle Status: Press and release F 2 times then press within 3 seconds, the transmitter will respond with one melody sound and display the current status of the vehicle.
• Display Illumination: Press and hold the F button for 1 second. The display will illuminate for 5 seconds.
• Melody / Vibration Mode: To have the remote control vibrate, play a melody tone or both each time it receives a response from the vehicle press F and release then press and hold Unlock for 2 seconds.
• Button Beeps: To toggle button beeps on or off press and release F then press and hold Start for 2 seconds.
• Battery Save Mode: While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any incoming signals from the main unit until a button is pressed. The LCD screen will display SAVE to indicate that power save mode is ON. To enter power save mode press and hold F for 5 seconds.
• Clear Flashing Icons and Melody Sound: Press the F button 3 times within 3 seconds. This will clear the melody sound and flashing icons on the LCD screen.
• Stopping LCD Trigger Melody: To stop the alarm trigger melody if the system has been triggered WITHOUT disarming the system, press any button one time only, this will not send a command to the vehicle at this time and the alarm will continue to sound.
• Button Lock: Press and release F then press hold Lock for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked.
• Illumination: Press and release F 2 times then press and hold Lock for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
• 2 Car Mode: To control a second security system enter 2 car mode by pressing F then press Lock and Unlock together for 3 seconds. When the II icon appears on the transmitter’s LCD screen it will control the second security system. Use the same method to exit 2 car mode and resume control of the original vehicle’s security system. NOTE: A second security system must be installed and the LCD transmitter must be learned to it before this feature will operate the additional system.
• Parking Meter Countdown: The parking meter countdown timer has 6 preset times, to access the preset times and begin countdown press F and release then press and hold Alarm for 2 seconds, each additional press of Alarm will increase the countdown time.
• Adjusting the Clock and Timer Settings: The clock, alarm clock and programmable countdown timer are accessed through the Function Menu. Press and hold F for 3 seconds to access the function menu, once you have accessed the feature menu press and release F to scroll through each feature. Press Alarm to increase or turn on. Press Start to decrease or turn off. Press and hold F for 2 seconds to exit the menu.

LCD Remote Control ICON’s

Transmitter Button Functions