Operating Instructions for PRO9544FT3 Remote Security System
|Arming the System - Active:||
|Silent Arming - Active:||
|Arming the System - Passive (Automatic):||
|Protection while the system is armed:||
|Disarming the System:||
|While the System is Sounding:||
If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected.
This feature is particularly useful if you are aware of children playing near your vehicle that may accidentally trigger your security system. In this case you can cancel the siren sounding without disarming your security system.
|Intrusion Warning Signals:||
This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren/horn will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered.
These intrusion warning indicators are stored in the system's memory and will only be erased when the ignition key is turned on.
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational.
To use the valet mode, the system must first be disarmed either by using your key chain transmitter, or by manually overriding the system:
Note: Always remember to exit the valet mode to ensure that the vehicle remains protected at all times.
|Using the Valet Switch Manual Override:||
Your security system can be disarmed without the use of the key chain transmitter. This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch Manual Override as indicated on the last page of your owner's manual, to bypass the alarm system:
Typically this override mode is used only if the transmitter has become inoperative.
|Programming Your Custom Override Code:||
To program you custom override code, programmable feature #9 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following:
If the new code was accepted, the unit will report back the newly entered code, by flashing the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the new code three times with a once second pause between each code, then the system will begin arming (if passive arming has been selected). If the LED flash pattern reports the previously stored code, the new code was not entered correctly. Please repeat steps 1 through 8 above considering the following:
|Using Custom Code Override:||
Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory:
|Eliminating the Normal Arm/Disarm Chirps:||
You can eliminate the chirps selectively any time you arm or disarm the system simply by holding the Arm/Disarm button for two seconds. If you find the normal arming and disarming chirps annoying, they can be turned off permanently, eliminating the need to hold the Arm/Disarm button for two seconds.
To eliminate chirps:
Note: If the siren/horn chirps two times, regardless of the valet switch operation as described above, then the horn and siren chirps have been turned off via programming features 7 and 8. Contact your installation center or Audiovox technical department for information on how to reinstate the chirp feature through programming.
Note: Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated.
|Remote Panic Operation:||
The Lock or Unlock button on your key chain transmitter also functions as a panic switch for use in emergency situations.
To use remote panic:
To stop the alarm:
Note: While in the Panic mode, pressing and releasing the Lock or the Unlock buttons will, if the option is installed, lock and unlock the doors respectively. While in the Panic mode, anytime the unlock button is pressed, the panic feature will continue for the allowed 30 seconds, however, the security system will be disarmed allowing the vehicle to start.
|Additional Remote Function (Channel 3):||
This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are:
To activate the optional accessory, press and hold the option button 2 on the key chain transmitter for 3 seconds.
For more detailed operating instructions, please refer to your Owner's Manual.
Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.
Before you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above.
NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.